straight method的例句大全

The Analytical Method of the Symmetric Figure for a Point, a Straight Line and a Plane

点、线、面对称图形的解析法

互联网摘选

Spiral bevel gears carbide skiving cutter has designed by method of inclination cut and straight line profile, and the generating surface of cutter is hyperbolic but conic.

根据斜角直线齿形造形方法设计出的弧齿锥齿轮刮削刀盘产形面已不再是一个圆锥面，而是一个双曲面。

互联网摘选

Regarding long straight pipes, the design replaces elastic analysis with stress analysis and uses directly buffed cold installation and preheating installation without expansion joint to replace compensatory directly buried method and cancels most compensators and anchor blocks trying to reduce construction cost and duration.

针对长直管道，以应力分析方法取代了弹性分析法，以无补偿直埋冷安装及预热安装取代了有补偿直埋敷设，取消了大部分补偿器及固定墩的设置，从而降低造价、缩短工期。

互联网摘选

The Initial Study on Reference Point Method of the Straight Sense of Mathematics

实行垂直整合的几点考虑数学直感的参考点方法初探

互联网摘选

By finding collinear points at edge of silicon chips and using straight line fitting method, the angle can be calculated.

该算法通过提取芯片边缘点的坐标点集和拟合直线参数来计算芯片的角度。

互联网摘选

Analytic Method for Computing the Successful Probability of Straight-forward Shooting by Sound-Guided Torpedo

计算声自导鱼雷直进射击成功概率的解析方法

互联网摘选

The method is straight-forward and efficient, since it reduces the nonstationary response problem to complex algebraic operations only.

方法简便实用，它将非平稳随机响应问题归结为复代数运算。

互联网摘选

The advantages of the proposed algorithm lie in that there is no need to decompose the original system, and the method is more flexible in a straight-forward way without much extra computation.

该算法的优点是不需对原系统进行分解，且得到的降阶系统阶数最低，计算量亦较小。

互联网摘选

Numerical calculation examples are given for the focusing of cosh Gaussian beams by an aperture lens. A comparison is made, which has shown the advantage of this method and the results are in good agreement with those obtained by the straight forward integration of Collins formula.

对双曲余弦高斯光束通过有光阑限制的薄透镜聚焦系统进行了数值计算，计算结果与直接由柯林斯（Collins）公式所得结果一致，且此解析方法便于进行物理分析，可节约大量机时。

互联网摘选

study on straight-line stabilization method for a class of chaotic economic model

一类混沌经济模型的直线控制法研究

互联网摘选

A stacking method for slalom line data-processing by curved-to-straight correction

弯曲测线多次覆盖资料处理中的校正叠加方法

互联网摘选

A New Method of Designing Deflection Crank Slider Mechanism Using Aided-straight (Circle)

利用辅助线（圆）设计偏置式曲柄滑块机构的新方法

互联网摘选

universal method for highway's horizontal alignment based on restrictions of straight line

基于直线约束的道路线形设计通用方法

互联网摘选

The combination of modified nance arch with straight wire arch technique is valid method.

改良Nance弓联合直丝矫治技术是一种有效的方法。

互联网摘选

Ease Curve Out-of-Range Types It presents the rigorous method to calculate the intersecting point coordinate of the straight line with the parallel to the easement curve.

减缓曲线越界循环类型提出了计算直线与缓和曲线平行线交点坐标的严密方法。

互联网摘选

By contrast, the test parameters corresponded to the three-shift gear when performance was good. From engineering perspective, it can be established that the parameter is the best straight-shift parameters This optimization method is proved feasible.

通过对比分析，验证该参数换档时所对应的三个换档性能指标都比较好，因此，从工程应用的角度来讲，可以认为该参数就是直线型换档的最佳参数，证明这种优化方法是可行的。

互联网摘选

For the centrifugal impeller blade composed of straight-line element, the grid generating method is developed with Cubic Non-Uniform B-Spline, and the corresponding program is completed.

采用三次非均匀B样条技术，对直纹面叶片的离心压缩机叶轮通道的网格生成方法进行了研究。

互联网摘选

Formulation of gargle method or chewing method, can make medicine from the outside to the inside, straight to penetrate the focus, with quick acting as a transmucosal absorption characteristics;

拟定含漱法或咀嚼法，可使药物由外而内，直透入病灶，具有显效快为特点一；

互联网摘选

The paper introduces a rapid calculation for gear change using ordinary function calculation in hobbing cylindrical straight gears with a teeth number greater or twice than a prime number over 100. This calculation method is simple, convenience and practical.

介绍了一种用普通函数计算器快速计算滚切齿数大于100的质数及其整数倍的直齿圆柱齿轮的挂轮。

互联网摘选

an analysis of motional and mechanical characteristics for double toggle clamping unit with straight five points of injection molding machine is made by the structural method.

利用机构学的方法对注射成型机五孔直排式双曲肘合模机构进行运动和力学特性分析。

互联网摘选