injection pressure的例句大全

Droplet Size Characteristics of Wall Impinging Diesel Fuel Spray at High Injection Pressure

高压喷雾碰壁的粒度特性研究

互联网摘选

this paper emphasizes on recounting structure features and technical measures for high injection pressure of pm pump.

着重论述了PM型喷油泵的结构特点和具有高喷射压力的技术措施；

互联网摘选

Therefore, using higher specific gravity and dynamic viscosity of biodiesel is able to decrease fuel injection pressure properly.

由此结果可知、比重和动力黏度较高的生质柴油，可适当的将燃料喷射压力减低是可行的。

互联网摘选

Injection pressure should be set low initially and increased to the point of filling the part just short of causing flash.

一开始应设定低的射出压力以填充零件至刚好不会造成毛边。

互联网摘选

The optimization parameters are production time 60d, steam dryness fraction 70%, cyclic steam injection volume 2 210 t, and steam injection pressure 4.0 MPa, stew time 3d, and steam injection velocity 220 t/ d.

优化结果为：生产时间60d，注汽干度70%，周期注入量2210t，注汽压力4.0MPa，焖井时间3d，注汽速度220t/d。

互联网摘选

lda measurement of droplet velocities in a high injection pressure diesel fuel spray

柴油机高压喷雾碰壁前后粒子速度的LDA试验研究

互联网摘选

Effects of High Injection Pressure and Swirl Ratio on DI Diesel Engine Performance

高喷射压力与涡流强度对直喷式柴油机性能的影响

互联网摘选

There is initial start pressure difference whatever for water flooding or water/ gas alternating displacement. So, increasing injection pressure should be done to start gas injection.

不论是水驱还是水气交替，都存在初始启动压差，要考虑增大注入压力以启动注气工程。

互联网摘选

The maximum injection pressure depends on the design of high pressure pump.

高压共轨系统最高喷射压力的高低是由高压泵的设计决定的。

互联网摘选

The packer sealing condition is valuated according to the variation of flow rate and pressure below injection flow regulator with injection pressure at the wellhead.

该技术是利用密封段密封配水器中心通道，通过改变井口注水压力来了解配水器以下的流量和压力的变化情况，判断封隔器密封状况。

互联网摘选

To meet the requirement of high-pressure common rail fuel injection system, the control strategy and mode was designed and the setpoint fuel injection pressure was calculated according to engine operating parameters.

基于GD1高压共轨电控燃油喷射系统，设计了燃油喷射压力的控制策略，根据柴油机的运行参数计算目标喷射压力并选择相应的控制模式。

互联网摘选

The result shows that, compared with polymer flooding, polymer cross link micro gel has more remaining amount in multi porous, poor mobility and high injection pressure, so it has a nice profile controlling displacement effect.

实验结果表明，与聚合物驱相比，由于聚合物交联微凝胶在多孔介质内滞留量大，流动能力差，注入压力高，因而调驱效果好。

互联网摘选

The article stated the change in temperature, injection pressure and injection time to get the lowest temperature and pressure and the shortest injection time.

介绍了利用注射成型工艺上的温度、压力变化及注射周期变化，找出适合某材料的最佳温度、压力及注射周期的方法。

互联网摘选

The phenomena, that the energy unavailability of oil wells and the anomaly of water injection pressure of water wells under the reasonable injection production ration in dynamic analysis was taken place frequently.

近几年在动态分析中经常发现在注采比合理的情况下，油井能量得不到保障或者水井注水压力反常。

互联网摘选

A Core Flow Study on Reducing Polymer Injection Pressure by Using Molecular Deposition Filming Composition HB

分子沉积膜剂HB降低聚合物注入压力实验研究

互联网摘选

The injection molding process of thermoset plastics bulk molding composition ( BMC) made of automobile lamp reflector is presented in the paper. Process parameters are settled such as barrel temperature, screw speed, injection pressure, injection velocity and holding time and so on.

介绍了热固性团状模塑料（BMC）注射成型汽车前照灯反射镜的工艺过程，确定了BMC注射成型的料筒温度、螺杆转速、注射压力、注射速度和保压时间等工艺参数。

互联网摘选

The injection pressure and gas flow uniformity of the injection tube in injection unit have significant effects on cleaning of filter-bag, which is one of the main technologies that need to be dealt with in large bag filter design process.

喷吹装置喷吹管喷吹气压和气量的均匀性对滤袋清灰效果影响显著，是大型袋式除尘器设计过程中需要解决的主要技术之一。

互联网摘选

It is shown that certain injection pressure is necessary for gas miscible displacement of oil to be carried on.

注气压力是形成油气混相驱替的必要条件；

互联网摘选

Due to high water injection pressure, it is difficult to transport the logging cable into water injection wll by its own weight during well logging process.

在注水井带压测试工艺中，由于注水压力的影响，测井电缆依靠自身质量无法向井下输送，为此开发研制了测井电缆带压下井输送器。

互联网摘选

part volume, runner-gate style and size, cavity locations, and injection pressure.

部分的音量，亚军门的样式和大小，腔的位置，和注射压力。

互联网摘选