heat distortion的双语例句-heat distortion造句-heat distortion的相关例句-英语网

1、

Improved heat distortion temperature and low ; temperature impact strength.

提高热变型温度和低温冲击强度.

互联网摘选

2、

Chapter 2 study the temperature and heat distortion, using finite element software to analysis GMA temperature field and the heat distortion.

第二章研究了GMA的温度场和热变形，使用有限元软件对GMA温度场及热变形进行了分析。

互联网摘选

3、

But comparing to metal, owing to MC its low strength, modulus and heat distortion temperature, bad size stabilization, and high notch sensitivity, the usefulness of MC nylon is still limited.

然而与金属相比，MC尼龙存在强度、模量和热变形温度较低，尺寸稳定性差，对缺口冲击敏感，因而限制其应用的范围。

互联网摘选

4、

Dynamic mechanical analysis showed that the heat distortion resistance and the temperature of abrupt drop point for tensile modulus E ′ increased markedly with the irradiation dose.

动态力学分析（DMA）分析表明，聚己内酯辐照交联后的弹性模量和耐热性能显著提高。

互联网摘选

5、

Suitable amount of wood powder was also helpful for the increase of composite tensile modulus, flexural property and heat distortion temperature, while it might decrease the impact strength and tensile elongation.

适量木粉能提高复合材料的拉伸模量、弯曲性能和热变形温度，但材料的冲击强度和断裂伸长率有所降低。

互联网摘选

6、

Thermal Analysis of Inertial Platform and Heat Distortion Test

惯性平台热分析与热变形试验研究

互联网摘选

7、

The results reveal that introducing bismaleimide into the cured system can improve the heat distortion temperature, flexural strength at high temperature and dielectric properties. In addition the reaction scheme of bismaleimide is mainly the self-polymerization but not copolymerization with epoxy group.

研究结果认为体系中引入双马来酰亚胺可提高热变形温度、热态强度和介电性能，双马来酰亚胺在固化中主要是自聚而不是和环氧基共聚。

互联网摘选

8、

convenient hardener for casting and laminating resin to obtain cured system of high heat distortion temperature

方便于浇铸和层压树脂高热变形温度固化系统

互联网摘选

9、

long - term heat distortion test method of polypropylene pall ring packing

聚丙烯鲍尔环填料长期热变形试验方法

互联网摘选

10、

Heat Treatment Distortion Control of the Main Shaft for Motorcycle Engine Transmission

摩托车发动机变速器主轴热处理畸变的控制

互联网摘选

11、

measures of decreasing heat treatment distortion for thin wall annular gear

减小薄壁内齿轮热处理畸变的措施

互联网摘选

12、

hardenability of carburizing steel and heat treatment distortion

渗碳钢的淬透性与热处理畸变

互联网摘选

13、

Deformation determines recrystallization score when it has same deformation temperature and heat preservation time. Deformation in the materials produced more distortion and can increase the recrystallization driving.

变形温度和保温时间相同时，变形量的大小决定了再结晶分数的大小，变形量的增大使材料内部产生了更多的畸变能，使再结晶的驱动力增大。

互联网摘选

14、

Its primary factor is the temperature distortion and the concrete shrinkage strain which the cement hydration heat produces.

产生裂缝的原因很多，其主要因素是水泥的水化热产生的温度变形和混凝土的收缩变形的共同作用。

互联网摘选

15、

Thermal Distortion Influence on Single-Slab Heat Capacity Laser Output

热畸变对单板条热容激光器输出的影响

互联网摘选

16、

analysis on distortion in heat treatment of bearing parts made of high carbon chromium steel

高碳铬轴承零件热处理变形分析

互联网摘选

heat distortion的例句大全