the intelligent grouping and resource sharing ( igrs) working group, home network standard industrialization alliance and china communications standards association ( ccsa) are three leading standardization organizations for home networks in china. they have made some achievements in standardization research of home networks.

1、

this paper simply introduces the situation about pushing the bidded budget, implementing low cost strategy and building total cost management system in the second highway engineering bureau of china communications construction group in the last ten years.

简要介绍了中交第二公路工程局有限公司近十年来推行标后预算、实施低成本战略、全面建立成本管理体系的情况。

互联网摘选

2、

the bridge, being built by the china communications construction company, will connect mal é with the island of hulhul é, where the mal é international airport is located.

这条由中国交通建筑公司建造的大桥，会连接Malé市与Malé国际机场所在地Hulhulé岛。

互联网摘选

3、

rubber asphalt sand gel is a science achievement of western china communications science& technology project "bridge deck laying material and technical research" regarding concrete bridge deck laying.

橡胶沥青砂胶是西部交通科技项目桥面铺装材料与技术研究在混凝土桥面铺装方面的一项研究成果。

互联网摘选

4、

and the making of an award shall be a condition precedent to any right of action against china communications insurance.

在公断人未作出公断书之前，被保险人不得对中国交通保险进行起诉。

provided by jukuu

5、

this article aimed to provide reference for the risk management of china communications construction company limited freeway bot project.

本文的研究旨在为中国交通建设集团后续高速公路BOT项目的风险管理提供借鉴。

互联网摘选

6、

network reconstruction project phase i of china communications planning& design institute for water transportation

中交水运规划设计院网络一期改造工程

互联网摘选

7、

china communications second highway survey, design and research institute

中交第二公路勘察设计研究院

互联网摘选

8、

china communications construction no.2 engineering bureau

中国通信建设第二工程局

互联网摘选

9、

china communications standards association information

中国通信标准化协会信息

互联网摘选

10、

surface roughness of bearing seatings

轴承支承面的表面粗糙度

互联网摘选

11、

tolerances for tapered journal seatings

锥形轴颈支承面的公差

互联网摘选

12、

dimensional, form and running accuracy of bearing seatings and abutments

轴承支承面与挡肩的尺寸、形状与运行精度

互联网摘选

13、

types of arrangement - bearings on cylindrical seatings and stepped shafts

配置类型——圆柱轴和阶梯轴上的轴承

互联网摘选

14、

the appropriate values for rolling bearing seatings on shafts are listed for the tolerances

与滚动轴承配合的轴公差值见表

互联网摘选

15、

bearing on stepped shafts and cylindrical seatings with 100 to 420 mm diameter .

阶梯轴和圆柱支座上的轴承，直径100-420毫米。

互联网摘选

16、

bearing on stepped shafts with cylindrical seatings with 140 to 710 mm diameter.

带圆柱支座阶梯轴上的轴承，直径140-710毫米。

互联网摘选

17、

推荐的圆柱形轴座配合要求可从表中查找。

互联网摘选

18、

figure 5 extends the concepts described earlier to address the presentation and updating of information about the current seatings.

图5扩展了先前描述的概念，从而解决了当前座位数信息的显示和更新。

互联网摘选

19、

tapered bearing seatings are checked using ring gauges , special taper gauges or sine bars .

圆锥形轴承基座则采用环规、专用锥度规或正弦规检查。

互联网摘选

20、

all seatings and surrounds shall be checked for line, level and bolt setting before commencement of fixing.

在螺栓开始固定之前，检查所有的支座和围护在同一直线和水平。

互联网摘选