A Study of Thermobalance Model for the Burning of Blended Coals

Experimental Investigation of Oil Shale Combustion Characteristics by the Use of a Thermobalance

油页岩燃烧特性的热天平试验研究

互联网摘选

Study on oxidation characteristics of steels under high temperature by differential thermobalance

利用差热天平研究钢在高温下的氧化特性

互联网摘选

By analyzing the pressure distribution between gears and sealing blocks in compound gear pump with three idlers, the resultant hydraulic forces acting on seal blocks are obtained.

通过对具有3个惰轮的定轴轮系复合齿轮泵各齿轮齿顶圆与密封块间的压力分布规律的分析，求出各齿轮与密封块间的液压油对密封块产生的液压力合力。

互联网摘选

Compared with traditional pulse generators, this pulse generator enhances the machining efficiency and surface quality of Micro WEDM. It can machine high quality micro gear with diameter of addendum 0.3 mm easily.

与传统的脉冲电源相比，此脉冲电源提高了微细WEDM速度和表面质量，并且能切割出高质量的齿顶圆直径为0.3mm的微小齿轮。

互联网摘选

The wear form of space gear mechanism in the vacuum environment was observed, and the degree of wear at the addendum, near the pitch and between the addendum and the tooth pitch, were analyzed by SEM.

采用扫描电镜分析了空间齿轮在真空环境下的磨损形式，同时分析了齿轮轮齿在齿顶、节圆附近以及齿顶和节圆之间的磨损程度。

互联网摘选

The essential meshing relationship, position of instantaneous center and the meshing range of the tooth head arc are discussed.

讨论了内外转子的基本啮合关系、瞬心的位置以及外转子齿顶圆的啮合范围等。

互联网摘选

The Influence of Tip Circle's Error on the Measuring Accuracy of Portable Tooth Profile Instrument

齿顶圆误差对上置式齿形仪测量精度的影响

互联网摘选

Deviation of Addendum Circle and Its Influence on Thickness Measurement of Gear-tooth

齿顶圆偏差对齿厚测量的影响及修正

互联网摘选

In this paper, we introduce the method to set up the measuring coordinate system and the analysis for the influence of the tip circle's error on the measuring accuracy of the portable instrument.

本文阐述了仪器测量时座标系的建立方法以及被测齿轮齿顶圆误差对测量精度影响的分析。

互联网摘选

Quantitative evaluation of residual endodontic microorganisms after mechanical root canal preparation different chemical preparations by real-time PCR The Method and Instrument of Measuring Addendum Circle and Dedendum Circle Diameter

感染根管机械预备联合不同化学方法预备后细菌残余量的实时定量检测齿顶圆与齿根圆直径的测量及其量具

互联网摘选

According to the results, the leakage area between rotor and stator take more than 70 percent of the total leakage area, is the main leakage path in the pump.

根据计算结果分析：转子齿顶圆面与泵腔内壁间构成的泄漏通道面积占总泄漏面积的70%以上。

互联网摘选

The transmission part is an involute gear, and the working part can adopt different working faces, such as a cylinder excircle face, a circular arc tooth or an involutes tooth gear top cavetto.

传动部分是渐开线齿轮，工作部分可采用不同的工作面，如圆柱外圆面或圆弧形齿或渐开线齿轮齿顶修圆。

互联网摘选

The spiral angle of graduated circle was rough estimated by measuring the addendum circle diameter and modified on milling machine.

测量齿顶圆直径估算分度圆螺旋角，用分度头在铣床上修正分度圆螺旋角，并进行误差分析。

互联网摘选

The Method and Instrument of Measuring Addendum Circle and Dedendum Circle Diameter

齿顶圆与齿根圆直径的测量及其量具

互联网摘选

The study of the stability is conducted of the zero oxygen equilibrium composition system of organics ( such as silicone oil, triethyl phosphate, wood powder, and cane sugar) and ammonium nitrate by the DSC thermoanalysis and the detonator susceptibility determination method.

以DSC热分析和雷管感度测定方法研究了硅油、磷酸三乙酯、木粉、蔗糖等有机物与硝酸铵按照零氧平衡组成体系的稳定性。

互联网摘选

Thermoanalysis Study on the Complex of Bis [ 1-( 2-Thienyl)-4,4,4-Trifluoro Butanedione-1,3] Copper(ⅱ) and its Adducts with Some Solvent Molecules

二[1-（2-噻吩基）-4,4,4-三氟丁二酮-1,3]合铜（Ⅱ）及其某些溶剂加合物的热分析研究

互联网摘选

Synthesis and Thermoanalysis of Comb-Polystyrene Epoxy-Ether Polyurethane

梳型聚苯乙烯环氧醚聚氨酯合成与热分析

互联网摘选

The main research includes the thermoanalysis and calculation of evaporator respectively adopting the separated region model and the node model, and the parametric drawing of the evaporator by using Visual Lisp.

针对不同的研究目的，分别采用分段模型与节点模型对蒸发器进行了热力分析与计算，并使用VISUAL LISP对蒸发器进行参数化绘图。

互联网摘选

Studies on the Joined Device of Microreactor-Gas Chromatography-Differential Thermoanalysis and the Kinetics of Oxidative Dehydrogenation of Ethanol to Acetaldehyde over Silver Catalysts

微反-色谱-DTA联合装置及乙醇催化氧化脱氢反应动力学的研究

互联网摘选

Thermoanalysis for dried ginger powder

干姜粉末的热分析研究

互联网摘选