The Microcomputer Automatic Standardization System of Tension-Meter in the Tension Test

1、

We put in here a tension meter, we put in here a tension meter and the bottom one, we hang on a string with a tension meter and then here we put four kilograms.

这儿放个张力计，这里也要一个，底下也有，一个张力计，挂着4kg物体。

互联网摘选

2、

A Pro/ E-based 3D parametric modeling and design method for anchor shank tension meter is proposed. Some problems that must be paid attention to be pointed out, and some key techniques are discussed.

提出了基于Pro/E的锚杆拉力计三维参数化设计方法，对造型设计中的技术要点进行了探讨，指出了应当注意的问题。

互联网摘选

3、

The principle for cable tension meter working on the basis of three points loading flexure is analyzed. The formula for determination of cable tension is deduced and justified by test.

通过对根据三点弯曲法原理设计的夹持式钢索张力测定传感器的研究，建立钢丝绳张力计算模式，用导出的钢丝绳张力计算公式计算，其结果与试验结果吻合较好。

互联网摘选

4、

The paper describes the application of GMS-500 tension meter of anchor rope in the greatly deformed deep underground cavity engineering in Meishan Iron Mine.

本文介绍了GMS－500型锚索测力计在梅山铁矿深埋大变形地下硐室工程中应用情况。

互联网摘选

5、

The morphological structure was observed by scanning electron microscope and video-zoom microscope, and the contact angle to water was determined by dynamic tension meter.

用扫描电子显微镜和视频变焦显微镜观察了改性烟用聚丙烯纤维的形态结构，用纤维表面动态张力仪测定了其对水的接触角。

互联网摘选

6、

Their CMC has been determined using Surface Tension Meter. The results demonstrated that the CMCs of those emulsifiers were much low.

利用表面张力仪测定其临界胶束浓度CMC值，结果表明所合成的乳化剂均具有较低的CMC。

互联网摘选

7、

Study on mine hoist wirerope tension meter

矿井提升钢丝绳张力检测仪的研制

互联网摘选

8、

3D solid design of anchor shank tension meter based on MDT

基于MDT的锚杆拉力计三维实体设计

互联网摘选

9、

Application of tension meter device in the strip shape measurement

基于张力测量的板形检测技术

互联网摘选

10、

An unbalanced layup has higher-strength laminations positioned on the tension side of the member and is typically used for simple-span beam applications.

非均衡复合材料铺层定位在组成的张力一侧，具有较高的强度分层，通常是应用于简单跨度梁；

互联网摘选

11、

Most members are designed to carry loads in tension, and the member is slim, the structure is bright and beautiful.

大部分杆件按受拉控制设计，从而实现了建筑要求杆件纤细、构通透、颖美观的目标。

互联网摘选

12、

The Conditionality of the Stress Formula of the Tension or Compression Member

论拉压杆应力分析公式的条件性

互联网摘选

13、

An important practical engineering problem is the stress distribution produced at or near a hole in a tension member when the load is applied to the pin or rivet filling the hole.

通过销钉或铆钉传递载荷的拉伸构件，发生在销钉孔周或孔的附近的应力分布，在工程实际中是一个重要的问题。

互联网摘选

14、

The Flex E are manufactured in polyurethane with a semi-elastic tension member.

半弹性多楔带用半弹性带芯与聚氨酯制成。

互联网摘选

15、

In the ordinary way, bonded reinforcement technology only suitable for reinforcing flexural& tension member that bearing static load.

粘钢加固技术一般只适用于加固承受静力作用的受弯及受拉构件。

互联网摘选

16、

For a groove welded tension member in3/ 4 in. plate, what is the maximum size of fusion discontinuity permitted in astatically loaded member?

对于3/4英寸板材的受拉构件坡口焊缝，在承受静载荷时，熔合性缺陷允许的最大尺寸是多少？

互联网摘选

17、

Study on optimal hybrid ratio of hybrid fiber composite tension member

混杂纤维复合材料受拉构件的最优混杂比研究

互联网摘选

18、

The compound control mode of speed control and tension control was used and the zero shift of the tension measuring device was compensated and spot-calibrated by software and hardware.

在控制方案上采用速度控制和张力控制的复合控制方式，同时通过软硬件对张力测定仪的零点漂移进行补偿和现场校正。

互联网摘选

19、

A computer control system was composed by paper web tension measuring device and paper machine drive system.

利用纸幅张力测定仪与纸机传动系统组成计算机控制系统。

互联网摘选

20、

In the paper, tension stringingconstruction management and technology operations precautions are briefly discussed.

文中就张力架线作业的施工管理以及工艺注意事项等进行了简要论述。

互联网摘选