3D solid design of anchor shank tension meter based on MDT

1、

Application of tension meter device in the strip shape measurement

基于张力测量的板形检测技术

互联网摘选

2、

An unbalanced layup has higher-strength laminations positioned on the tension side of the member and is typically used for simple-span beam applications.

非均衡复合材料铺层定位在组成的张力一侧，具有较高的强度分层，通常是应用于简单跨度梁；

互联网摘选

3、

Most members are designed to carry loads in tension, and the member is slim, the structure is bright and beautiful.

大部分杆件按受拉控制设计，从而实现了建筑要求杆件纤细、构通透、颖美观的目标。

互联网摘选

4、

The Conditionality of the Stress Formula of the Tension or Compression Member

论拉压杆应力分析公式的条件性

互联网摘选

5、

An important practical engineering problem is the stress distribution produced at or near a hole in a tension member when the load is applied to the pin or rivet filling the hole.

通过销钉或铆钉传递载荷的拉伸构件，发生在销钉孔周或孔的附近的应力分布，在工程实际中是一个重要的问题。

互联网摘选

6、

The Flex E are manufactured in polyurethane with a semi-elastic tension member.

半弹性多楔带用半弹性带芯与聚氨酯制成。

互联网摘选

7、

In the ordinary way, bonded reinforcement technology only suitable for reinforcing flexural& tension member that bearing static load.

粘钢加固技术一般只适用于加固承受静力作用的受弯及受拉构件。

互联网摘选

8、

For a groove welded tension member in3/ 4 in. plate, what is the maximum size of fusion discontinuity permitted in astatically loaded member?

对于3/4英寸板材的受拉构件坡口焊缝，在承受静载荷时，熔合性缺陷允许的最大尺寸是多少？

互联网摘选

9、

Study on optimal hybrid ratio of hybrid fiber composite tension member

混杂纤维复合材料受拉构件的最优混杂比研究

互联网摘选

10、

The compound control mode of speed control and tension control was used and the zero shift of the tension measuring device was compensated and spot-calibrated by software and hardware.

在控制方案上采用速度控制和张力控制的复合控制方式，同时通过软硬件对张力测定仪的零点漂移进行补偿和现场校正。

互联网摘选

11、

A computer control system was composed by paper web tension measuring device and paper machine drive system.

利用纸幅张力测定仪与纸机传动系统组成计算机控制系统。

互联网摘选

12、

In the paper, tension stringingconstruction management and technology operations precautions are briefly discussed.

文中就张力架线作业的施工管理以及工艺注意事项等进行了简要论述。

互联网摘选

13、

The Development, Design and Application of Surface Tension Propellant Management System

表面张力推进剂管理系统的发展、设计与应用

互联网摘选

14、

It obtains the deformation and failure mechanism of the steel skeleton reinforced HDPE under tension and bending load conditions.

钢网增强HDPE复合材料的受拉伸与弯曲载荷条件下的形变与破坏机理。

互联网摘选

15、

Tension control and load distribution are key and difficult issues too. Their control strategies have been improved with the improving requirements.

张力控制和负荷分配控制都是纸机传动控制中的关键点和难点，控制方法也在随着纸机工艺要求的提高而不断改进。

互联网摘选

16、

Computational method on axial tension of secondary load RC members strengthened with carbon fiber reinforced plastic sheets

碳纤维布增强二次受力RC构件轴拉计算方法

互联网摘选

17、

Finally, speed chain, tension control and load distribution were realized by programming to hardware in the laboratory.

最后在实验室搭建的硬件平台上进行了程序的编写和调试，实现了速度链控制、张力控制和负荷分配控制。

互联网摘选

18、

Fatigue Durability Testing of Differently Shaped Screws under Combined Tension and Bending Load

不同类型螺栓复合拉弯时的疲劳强度研究

互联网摘选

19、

Design Method of Moment-strengthening on Tension Side When Load Un removed

非卸载条件下受拉区加固梁的抗弯设计法

互联网摘选

20、

Nomograph for tension calculation of load carrying rope and its application

承载索张力计算诺模图及其应用

互联网摘选