cone angle

Through the simulation concluded that: hydraulic damping hole diameter, cone angle valve, column, liquid supply pipe diameter, top beam diameter and column stiffness on column uninstall impact significantly.

通过仿真得出：液控口阻尼孔直径、阀芯锥角、立柱直径、供液管路直径、顶梁及立柱刚度对立柱卸载冲击影响明显。

互联网摘选

However, its performance will deteriorate obviously when the detector array widen and cone angle largen.

然而，当检测器阵列变宽、射束锥角变大时，其应用性能总体将明显趋于恶化。

互联网摘选

The test results show that the zinc coat loss can be reduced as pass draughts increase by raising work cone angle rationally and reducing the bearing length, but which has not obvious effect on the mechanical properties of finished steel wire and the service life of die.

试验结果表明部分压缩率增大时，合理增大工作锥角度、减少定径带长度，可减少锌层质量损失，而对成品钢丝的力学性能和模子寿命影响不明显。

互联网摘选

the computing formula of theoretical cone angle of the worm addendum cone and dedendum cone can be derived from the character of involute conical worm-gear.

根据渐开线锥蜗杆蜗轮啮合上的特点，推导出蜗杆齿顶圆锥的理论锥角计算公式及齿根圆锥的理论锥角计算公式；

互联网摘选

method to measure inner cone angle with sine protractor

用正弦规测量内锥角的方法

互联网摘选

It calculated the cone angle of the punch and gave out the radial equation of the punch as well as the equation of the spring.

计算出凸模锥面角度值，给出凸模径向运动方程式及弹簧力表达式。

互联网摘选

This paper emphatically introduced the reformation scheme of cone angle setting mechanism on warper.

重点介绍了整经机上圆锥角调节机构的改进方案.

互联网摘选

Study of Mold Cone Angle of Hydraulic Briquetting Press Based on ANSYS

基于ANSYS的生物质液压成型模具锥角优化

互联网摘选

The spotlight and physical light shaders have a button to easily match the cone angle to the maya setting.

聚光灯的灯光的锥形角度（照射范围角度）和物理灯光材质通过一个按钮可以轻易的匹配。

互联网摘选

Optimizing Design on Punch Cone Angle of Motor Commuter

电机换向器整体冷锻模冲头端部锥角优化设计

互联网摘选

To provide a theoretical basis for the conical stylus cone angle selection. ( 2) Analysis of the stylus tip radius and the stylus static pressure causing timber roughness parameter measurement error, calculation of the roughness measurement error value caused by the different tip radius.

分析触针针尖圆角半径和触针静压力引起的木材粗糙度测量误差，计算不同针尖半径造成的粗糙度测量误差值。

互联网摘选

It has been derived a formula of cone angle of femal die when two-piece cans thinned and drawn under the condition of the minimum resistance of deformation by using the energy method.

用能量法推导出两片罐变薄拉深时，毛坯变形抗力最小条件下的凹模锥角表达式。

互联网摘选

the computing formula of theoretical cone angle of the wormwheel addendum cone and dedendum cone can be derived yet.

推导出蜗轮齿顶圆锥的理论锥角计算公式及齿根圆锥的理论锥角计算公式。

互联网摘选

fabrication of large cone angle optical fiber probe by dynamic chemical etching method

动态化学腐蚀法制备大锥角近场光纤探针

互联网摘选

The new flash boiling spray model predicts spray tip penetration and spray cone angle and its development trend, in good agreement with the experimental results.

模拟结果表明，闪急沸腾喷雾新模型较好的预测了喷雾贯穿距及喷雾锥角及其发展趋势，喷雾图像与实验结果吻合较好。

互联网摘选

In diesel premixed combustion mode, the effects of nozzle cone angle on emissions were studied.

进行了在柴油可控预混压燃燃烧模式下, 油嘴喷射锥角对燃烧与排放的影响研究.

网络文摘精选

Cone Angle of Female Die of Two-Piece Can in Thinning Drawing Based on the Minimum Resistance of Deformation

基于最小变形抗力条件下的两片罐变薄拉深凹模锥角

互联网摘选

The research shows that when cone angle is less than some value, its increase will decrease the deformation of an anchor and raise its field load greatly, and for a mono-strand anchor, reasonable cone angle varies from 6.5 ° to 7.5 °.

研究表明，当锥角小于某值时，较大的锥角能明显减小锚具变形；对于单孔锚具，合理的锥角介于6.5°～7.5°之间。

互联网摘选

Analysis on Error of Measuring Cone Angle in Spheroid ( Cylinder) Way

圆球（柱）法测量锥顶角的误差分析

互联网摘选

In the process of exploitation, we use a new idea of "pitch cone radius not modification, reference cone angle modification." and order function of "Program" of Pro/ E system to reach parametrical control of assembles of die.

在开发过程中，利用节锥不变、分锥变位的新思路和Pro/E系统中的Program命令功能达到模具组件的参数化控制。

互联网摘选

In this paper, the fuel spray penetration, cone angle and droplet size distribution of a conical nozzle are investigated by using laser technique, qnd the fuel spray characteristics of the conical nozzle are compared with those of multihole nozzles.

本文应用激光技术对伞喷喷油嘴的喷雾贯穿距离、喷雾锥角、喷雾粒径及其分布等进行了研究，并对伞喷喷油嘴与多孔喷油嘴的喷雾特性进行了比较。

互联网摘选