wear loss

The results indicate that the wear loss obey normal distribution.

经分析发现磨损量服从正态分布。

互联网摘选

In order to decrease the cutter consume and the time loss of machine standing, to enhance the utilization of TBM, the abnormal cutter wear of TBM needs to be recognized in time.

TBM刀具磨损的预测和异常磨损识别方法的确定，对于保障TBM的安全掘进以及提高其利用率和经济性具有重要意义。

互联网摘选

Wear loss decrease as speed increases and reach a plateau when speed reaches certain value.

在一定转速范围内，磨损量随着转速的增加而减小，减小到一定值后趋于平稳。

互联网摘选

The relationship of abrasion loss and friction coefficient with respect to load, sliding velocity and sliding distance are discussed and wear mechanism of ceramic is analyzed.

对氧化铝陶瓷的耐磨损性能进行了检测与分析，讨论了载荷、滑动速度、滑动距离与磨损量、摩擦系数之间的关系，分析了陶瓷磨损过程机理。

互联网摘选

The corresponding relationship between high temperature impacting numbers and wear loss of hot work die steels are studied by weight loss method.

用失重法研究五种热作模具钢的热磨损次数与磨损量的对应关系。

互联网摘选

The result shows that in the ring-block sliding wear test, with time prolonging, the friction coefficient of all samples becomes more and more stable, and the mass wear loss increases.

结果表明：在环-块滑动摩擦实验中，随时间延长，试样摩擦系数均趋向平稳，质量磨损量均增长。

互联网摘选

The surface grain size and thickness of scale vary with temperature, and the initial wear loss increases with increasing grain size, and same tendency is observed for the total wear loss vs the thickness of scale.

膜表面晶粒大小和厚度随着温度而变化，膜初速磨损量和总磨损量随着成膜温度的变化分别与表面晶粒大小和膜厚相对应；

互联网摘选

Under a low load of 50-100 N, there was not apparent influence of microstructure on wear loss. With increasing the load, the microstructures markedly affected wear loss. The wear loss increased with increasing tempering temperature and reducing hardness.

在50-100N的低载荷下，不同回火组织的磨损失重变化不大，随着载荷增大，回火组织对磨损失重有显著影响，磨损失重随着回火温度的升高和硬度降低而增加。

互联网摘选

Osteoarthritis is due to wear and tear with loss of articular cartilage.

骨关节炎源于关节软骨的磨损破坏甚至丧失.

互联网摘选

Inadequate resistance to wear will lead to rapid loss of clearances and drop in pump performance.

如果耐磨蚀能力不足,则将导致间隙迅速增大和泵性能下降.

互联网摘选

According to the analysis of the performance of antifriction by using abrasion tester, coefficient of friction and wear loss were measured on the conditions of regular feeding oil and no oil.

采用摩擦试验机对所制备的产物的抗磨性进行了表征分析；确定了正常供油状态下和无机油状态下，该纳米抗磨剂的摩擦因数及其磨损量。

互联网摘选

Under low load of 62 N the main mechanism governing wear properties of ADZ ceramic is apparent plastic deformation and ploughing, wear loss is controlled by plastic deformation, micro-cutting, and micro-rupture under 124 N;

在62N低载荷条件下，10ADZ陶瓷的磨损机制以犁沟和塑性变形为主；在124N载荷下其主要的磨损形式为塑性变形、微切削和微断裂；

互联网摘选

The term of tooth wear ( TW) is used to describe the loss of hard tooth tissue caused by friction between tooth occlusal facing or tooth facing and food during masticatory movement and non-masticatory movement under no occurrence of dental caries and external injury.

牙齿磨耗是指在没有龋齿及外伤情况下，牙齿在咀嚼运动和非咀嚼运动过程中，由于牙面与牙面间摩擦、牙面与食物间摩擦，牙齿硬组织的丧失。

互联网摘选