tooth point的例句大全

it pointed out that the design of gear cutter should greatly increase the tooth point arc so as to reduce the stress concentration to increase the force of tooth root.

指出通过计算作出图形，可分析出滚刀齿顶圆弧的设计是否合理。

互联网摘选

The QX straight conjugate internal gear pump is a new type of hydraulically driving element. The calculation of tooth profile, the limiting point of meshing, the designing process of slotting cutter were introduced.

介绍了一种新型液压动力元件&QX型直线共轭内啮合齿轮泵的齿廓曲线计算、专用插齿刀具设计方法，分析了齿廓啮合极限点。

互联网摘选

Firstly, the data of the surface ′ s point of a tooth are gotten from the spiral bevel gear tooth surface equation, then, the whole tooth surface data are formed through converting the previous data.

首先，根据弧齿锥齿轮的齿面方程求出一个轮齿的齿面上点的数据，然后经过旋转变换便形成全部齿面的数据。

互联网摘选

If the sliding piece was pulled off the steering shaft, the notch must point towards the tooth gap during assembly.

如果滑动件被从转向轴上拔下，则在装配期间切口必须指向齿隙。

provided by jukuu

A New Method for Solving Instant Meshing Point of Real Tooth Surface& Zero Gape Method

真实齿面瞬时啮合点求解算法的研究&零间隙法

互联网摘选

Utilizing the theory of differential geometry, elastic deformation and wear abrasion and running-up of the tooth surfaces in circular arc gears, an elastohydrodynamic lubrication ( EHL) model of point contact with two-dimensional surface velocities was developed.

从圆弧齿轮齿面微分几何分析、弹性接触变形和跑合磨损分析，建立了具有二维表面速度的点接触弹流基本模型。

互联网摘选

Finally, through an example, the paper get a maximum stress point and stress distribution on a belt tooth and compare them with the solution of fixable plane problem.

最后，通过一个具体算例求出梯形齿同步带一个齿上的最大应力点及应力分布规律并与弹性平面问题的解进行了比较。

互联网摘选

The relatively velocity's computing formulas of this new spatial cam sliding tooth precision transmission meshing joggle's each contacting point are deduced, and the data computing are accomplished.

推导了新型空间凸轮活齿精密传动啮合副各接触点相对速度的计算公式，并进行了数值计算。

互联网摘选

on point image recognition and measurement of a spiral bevel gear's tooth surface

螺旋锥齿轮齿面点图像识别及其测量技术

互联网摘选

an analysis of the meshing pitch point of a pair of gears by the differential equation of conjugating tooth profile

由共轭齿廓的微分方程分析齿轮的啮合节点

互联网摘选

lower serratus anterior muscle angle between teeth, muscle fibers within the tooth to just point to the anterior radial distribution center.

前锯肌下部肌齿之间存在夹角，肌齿内肌纤维以止点为中心呈放射状向胸前外侧分布；

互联网摘选

In down milling , maximum chip thickness cecum close to the point tooth contacts the work.

顺铣时, 最大切屑厚度产生于靠近刀具与工件接触点处.

网络文摘精选

These formulae are suitable for any contacting point of tooth surface meshing.

这些公式适用于齿面啮合的任何接触点.

互联网摘选

Study on solution of engaging tooth contact point trace line by network method

网络法求解相啮合齿面接触迹线的研究

互联网摘选

Pitch Point is the intersection of the spline tooth profile with the pitch circle.

节点是键齿的齿廓与节圆的交点.

互联网摘选

Two formulas of compound shaper cutter are ob-tained. They are used to calculate the pitch pressure angle of chamfer involute and radius of circle on which chamfer involute starting point lies, and to check the tooth root slot width.

得到了复合插齿刀倒角渐开线分度圆压力角，倒角渐开线起始点所在圆半径的设计公式及插齿刀齿根槽宽的验算公式；

互联网摘选

Pitch Point is the intersection of the spline tooth profile with the pitch circle.

节点是键齿的齿廓与节圆的交点.

互联网摘选