temperature bath的例句大全

Sixty min after sponge bath, the rate of the elevated temperature was 41.5%, 30.0% and 19.1% separately in groups A, B and C ( P < 0.01).

3组擦浴后60min体温回升率分别为41.5%、30.0%、19.1%，3组比较，差异有显著性意义（P

互联网摘选

The boby temperature was measured before and after the sponge bath. Results The effective rate of body temperature lowering was 77.4%, 86.0% and 95.7% respectively in groups A, B and C with the difference being significant ( P < 0.01).

结果甲、乙、丙3组擦浴后体温下降有效率分别为77.4%、86.0%、95.7%，3组比较，差异有显著性意义（P

互联网摘选

features of American life which I find really tiresome, the impossibility of getting a bath in the ordinary sense, and their ideas on room temperature.

美国人的生活方式很讨厌，你找不到一个真正意义上的浴缸，而且他们对室温的看法也很讨厌。

互联网摘选

Design of a Multichannel Temperature Measurement System for Full-automatic Liquid Bath

全自动恒温液槽中多路温度测量系统的设计

互联网摘选

The gel spinning process of high-performance PVA fiber was described, and the influential factors including fiber structure, drawing process, solvents, coagulant varieties and coagulation bath temperature, etc. were discussed.

详述了凝胶纺丝制备高性能PVA纤维的工艺及其影响因素：纤维结构、拉伸工艺、溶剂、凝固剂种类、凝固浴温度等。

互联网摘选

the ultrafiltration rate of pure water with the coagulation bath temperature increased.

随着凝固浴温度的升高，所成的膜的透水速率上升。

互联网摘选

the results showed that the properties of the regenerated bamboo fiber prepared with lower coagulation bath temperature were improved.

实验结果表明：在较低的凝固浴温度下纺制得到的再生竹纤维素纤维的性能较好。

互联网摘选

the water flux increases along with the prolonging of pre-evaporation and the increasing of coagulation bath temperature.

水通量随着预蒸发时间的延长、凝固浴温度的上升而上升；

互联网摘选

several spinning procedure conditions were discussed, such as coagulation bath concentration, temperature, extruding rate and core layer liquid flow rate etc.

并对凝固浴浓度和温度、挤出速率、芯液流量等纺丝工艺条件进行了探讨。

互联网摘选

the results show that spinning and fiber properties are influenced by the concentration of the solvent in the coagulating bath and the temperature of the coagulating bath.

结果表明：凝固浴中溶剂浓度对纺丝过程及纤维强度有重要影响，而凝固浴温度对纤维的影响相对较小；

互联网摘选

the effects of resin type, temperature and dimethyl formamide ( dmf) contents in the coagulating bath, resin and filler contents in the coating solution, drying temperature in the baking oven on the properties 4| of the pu synthetic leather are discussed.

重点讨论了树脂种类、凝固槽温度和二甲基甲酰胺（DMF）浓度、涂布液中树脂和填充剂含量、烘箱的干燥温度等主要因素对PU人造革性能的影响。

互联网摘选

porosity increases along with the increasing of coagulation bath temperature, and doesn't have relation to pre-evaporation.

孔隙率随着凝固浴温度的上升而上升，而与预蒸发时间的长短没有关系；

互联网摘选

through comparing the membrane performance at different coagulation bath temperature, the higher the coagulation bath temperature, the higher the pure water flux.

比较不同凝胶浴温度下的膜分离性能可以看到，凝胶浴温度提高可以显著提升膜的纯水通量。

互联网摘选

the effects of spinning dope concentration, coagulation bath temperature and addition of persimmon leaves on the mechanical properties of blend fiber were studied.

研究了纺丝原液浓度、凝固浴温度、柿叶添加量对共混纤维的力学性能的影响。

互联网摘选

lifting the temperature of coagulation bath caused the decreasing of the inner and outer diameter and increasing of the maximum pore size and pure water flux.

改变凝固浴温度发现，凝固浴温度的升高会减小膜的内、外径尺寸，水通量和最大孔径增大。

互联网摘选

the retention rates of albumin bovine decreases when coagulation bath temperature increases, and first decreases, then increases when pre-evaporation time prolongs.

对牛血清白蛋白的截留率随着凝固浴温度的上升而下降，随着预蒸发时间的延长先略有下降然后上升。

互联网摘选

the structure of membrane is compact when the coagulation bath temperature is below 10 ℃, but the structure of it is loose with the coagulation bath temperature increasing;

结果发现，凝固浴温度低于10℃时，膜结构致密；随着浴温的逐步升高，膜结构变得疏松；

互联网摘选

it was noted that when coagulation bath temperature was increased, crystallization could be suppressed, and more porous structure was obtained on the surface of the membrane.

另外，凝胶浴温度升高可以抑制结晶现象，并使膜表面孔径和孔密度增加。

互联网摘选

sulfuric acid, ammonium chloride, sodium hydroxide and ethanol were selected as coagulation bath under different coagulation temperature and coagulation time to manufacture hec membranes.

分别选取硫酸、氯化钕、氢氧化钠和乙醇等溶剂作为凝固浴，在不同凝固温度和凝固时间下凝固制备HEC膜。

互联网摘选

the experimental results indicated that low temperature of casting solution and coagulation bath, short evaporation time and low polymer concentration of casting solution tend to increase the effective porosity of membrane.

实验结果表明较低的铸膜液温度和凝胶浴温度、较短的蒸发时间和较低聚合物浓度有利于增加膜的有效孔隙率。

互联网摘选