flexural strength的例句大全

Fine ceramics ( advanced ceramics, advanced technical ceramics)-test method for flexural strength of monolithic ceramics at elevated temperature

细陶瓷-单块陶瓷高温弯曲强度试验方法

互联网摘选

Determination of the Flexural Strength of GI-ⅰ Slip Casting Aluminous Ceramic Core

GI－Ⅰ型粉浆涂塑铝瓷核冠底层抗弯强度的测定

互联网摘选

Study on preparation methods and mechanical properties of high flexural strength cement concrete with heavy vehicle

重载高抗折强度水泥混凝土的配制及其力学性能研究

互联网摘选

Study on the flexural strength of 12 different non-metal core materials

12种非金属核材料的弯曲性能研究

互联网摘选

Factors influencing compressive and flexural strength of NPRC were simulated and the theoretical strength of NPRC was calculated.

分析了影响透水性再生混凝土抗压、抗折强度的因素，计算了活性粉末透水性再生混凝土的理论强度。

互联网摘选

The results reveal that introducing bismaleimide into the cured system can improve the heat distortion temperature, flexural strength at high temperature and dielectric properties. In addition the reaction scheme of bismaleimide is mainly the self-polymerization but not copolymerization with epoxy group.

研究结果认为体系中引入双马来酰亚胺可提高热变形温度、热态强度和介电性能，双马来酰亚胺在固化中主要是自聚而不是和环氧基共聚。

互联网摘选

The results generally indicate that the flexural strength of the repaired beams is increased, but the ultimate load of beams with tension delamination failure is reduced relatively.

试验结果表明，玻璃纤维布加固的钢筋混凝土梁抗弯承载力显著提高，发生剥离破坏的试验梁极限荷载相对地有所降低。

互联网摘选

Based on test, the article has analyzed the influence of freeze-thaw cycles to concrete compressive strength, flexural strength and cleavage strength, then approached mechanism of fracture by freeze-thaw on micro-structure.

通过试验分析了冻融循环对混凝土抗压、抗折、劈拉强度的影响，并从微观结构探讨了混凝土冻融破坏机理。

互联网摘选

Mechanical performance test includes the cube compressive strength, elastic modulus, axial compressive strength and flexural strength test.

力学性能试验包括立方体抗压强度、弹性模量、轴心抗压强度和抗折强度试验。

互联网摘选

Some conclusions are drawn: the compressive strength and flexural strength of cubic specimens of steel fibre reinforced concrete increase with the dosage of steel fibre;

结果表明：钢纤维混凝土立方体的抗压强度、抗弯强度随着钢纤维掺量的增加而增大；

互联网摘选

The results show that the thermoplastic sheets and the flow molded parts have superior mechanical properties, that is, tensile strength, flexural strength, modulus and impact strength are greater than 60 MPa, 100 MPa, 3 500 MPa and 50 kJ/ m2 respectively.

结果表明：三种热塑性复合材料片材与制品具有优异的力学性能，拉伸强度、弯曲强度、模量和冲击强度分别大于60MPa、100MPa、3500MPa和50kJ／m2，热变形温度158℃左右。

互联网摘选

Objective: This study was used to evaluate the flexural strength of three kinds of resin composite core materials with a method of three-point bending test.

目的：采用三点弯曲实验的方法测量3种复合树脂核材料的弯曲强度。

互联网摘选

Methods Flexural strength and elastic modulus were measured by three-point bending test at selected temperatures from 830 C to 950. X-ray diffraction was used to investigate the type of crystal and crystal percentage.

方法按不同晶化温度条件分组，利用X射线衍射技术鉴定晶相，计算晶体含量，并采用三点弯曲法测定各组的抗弯强度和弹性模量。

互联网摘选

60 groups of data are obtained on the basis of an analysis of traffic, variant stabilized base course thickness and different concrete pavement flexural strength.

对不同飞机类型和交通量（包括单一机型和混合交通）条件下，不同基层厚度和面层强度的60组混凝土道面结构进行了厚度计算分析。

互联网摘选

The compressive and flexural strength of styrene-butadiene rubber ( SBR), polyacrylic ester ( PAE) and polystyrene-acrylate latex ( SAE) modified self-levelling mortars with different polymer binder ratio at different ages were compared.

研究了不同掺量的丁苯乳液（SBR）、丙烯酸酯乳液（PAE）和苯丙乳液（SAE）对自流平砂浆不同龄期下的抗压、抗折强度的影响。

互联网摘选

The results show that under same flowability of all fresh mortars, the compressive and flexural strength of latex-modified mortars at 3 d demonstrate a parabolic shape curves with increasing the amount of the polymer.

结果表明，在新拌自流平砂浆流动度相同的条件下，3种聚合物改性砂浆的3d抗折、抗压强度随聚合物掺量的增加均表现出抛物线型变化趋势。

互联网摘选

The flexural strength of sintered bodies increases from 11.5 MPa to 19.6 MPa with the solid loading increasing from 50% to 80%, corresponsively.

烧结后的炭制品当固含量的体积百分数从50%增加到80%时，相应的抗弯强度从11.5MPa增加到19.6MPa。

互联网摘选

Nonlinear thermal buckling for composite laminate with elliptical delamination The test and calculation for the flexural strength of carbon fibre laminate composites

含椭圆形分层损伤层合板的非线性热屈曲碳纤维复合材料层压板弯曲强度的测试与计算

互联网摘选

Cordierite ( MAS) and MAS/ SiC multiphase material were prepared, and then the multiphase material's bulk density, open porosity, flexural strength and thermal-shock resistance were measured.

合成堇青石（MAS）并制备MAS/SiC复相材料，测试了复相材料的体积密度、开口气孔率及抗热震性等。

互联网摘选

Slip casting aluminous ceramic crown is a new all-ceramic system with high flexural strength, optimum marginal fit and improved aesthetics.

粉浆涂塑铝瓷冠是新近推出的一种全瓷修复系统，具有强度高、边缘适合性好透光性好等诸多优点。

互联网摘选