transfer function identification of electro-hydraulic servo system for coiler's wrapper rolls

1、

study on surfacing technologies of wrapper rolls and deep camber rolls used for rolling mill

轧钢助卷辊和深弯辊堆焊技术研究

互联网摘选

2、

standard practice for the operation of the tetrapod walker drum tester

四撑点式地毡踩踏滚筒试验仪的操作

互联网摘选

3、

textile floor coverings; tetrapod walker apparatus; constructional details and instructions for use

铺地织物.四撑点式步行试验仪.构造细节和使用说明

互联网摘选

4、

spillway: safety design, prevent the faucet water not overflow trough is caused close.

防止因水龙头未关而造成水溢出槽体。

互联网摘选

5、

a model of material removal rate with fixed abrasive pad

固结磨料抛光垫作用下的材料去除速率模型

互联网摘选

6、

mathematic model of material removal rate for ultrasonic milling

超声波铣削加工材料去除率的理论模型

互联网摘选

7、

study on modeling of material-removal-rate in ultrasonic machining and experiments

超声波加工工艺的材料去除率建模及试验研究

互联网摘选

8、

effect on material removal rate of fluid jet polishing by several parameters

液体喷射抛光时各工艺参数对材料去除量的影响

互联网摘选

9、

dependency of material removal rate on velocity in cmp of microelectronic materials

微电子材料CMP加工中去除率与速度的关系

互联网摘选

10、

optical components; magnetorheological finishing; mr fluids for finishing; material removal rate; surface roughness; removal depth;

光学零件；磁流变抛光；磁流变抛光液；材料去除率；表面粗糙度；去除深度；

互联网摘选

11、

material removal rate study of wire electrical discharge machining pocketing

线电极放电铣削凹坑的材料去除率规律研究

互联网摘选

12、

experimental study on influences of dispersant on material removal rate and the surface roughness of cu cmp

分散剂对铜CMP材料去除率和表面粗糙度影响的实验研究

互联网摘选

13、

edm in gas can make less electrode wear, but its high short circuit ratio will lead to unstable process and thus low material removal rate.

气中电火花加工时电极相对损耗很小，但由于短路率过高导致加工不稳定、材料去除率不高，还会产生烧焦气味。

互联网摘选

14、

experiment results showed that wedm in atmosphere offers advantages such as better straightness and higher material removal rate.

实验结果表明，气中线切割加工具有加工表面直线度好、加工速度（材料去除率）高等优点。

互联网摘选

15、

when establishing the optimization model, the material removal rate was set as one constrain.

设计优化数学模型时，将金属去除率作为一个约束条件。

互联网摘选

16、

the result indicated that the material removal rate of impulse generator is over 20% higher than that of general pulse generator.

实验结果表明，与普通脉冲电源相比，等能量脉冲电源可以提高加工效率20%以上。

互联网摘选

17、

the simulation of material removal rate, one of the key processes of the multi-mode combined polishing, was described in detail.

描述了多模式组合抛光的关键技术之一，材料去除率仿真模型的建立方法。

互联网摘选

18、

the effect of mineral component grain composition on cbr value

颗粒组成、矿物成分对CBR值的影响

互联网摘选

19、

study on mineral component and micro-morphology of white cement by soda residue

碱渣烧制白水泥熟料显微结构的研究

互联网摘选

20、

study on characters and mineral component of nephrite from california and burma

加州软玉和缅甸软玉特征及矿物成分的研究

互联网摘选