A truck longeron production design and technic optimize are accomplished by CAE software KMAS, an operate method which can get optimization result is put forward in automotive body panels and die design.

1、

Application of CAE Software KMAS for Sheet Metal Forming in Auto-Body Component Design and Pre-analysis of its Formability

KMAS冲压分析CAE软件在车身件设计及工艺预分析中的应用

互联网摘选

2、

As the shape technology of triangle chassis canister is analyzed, then the processes of bending, stretching and bulging compound mould are adopted to reunite the shape.

对三角形底盘筒形件的成形工艺进行了分析，决定采用弯曲、拉深、胀形复合模等进行复合成形。

互联网摘选

3、

Compound Mould for the Triangle Chassis Canister

三角形底盘筒形件复合模

互联网摘选

4、

As part of the platform redesign, different versions of the vehicle floor stampings were created to accommodate batteries or compressed natural-gas storage.

作为平台重新设计的变动之一，不同版本的底盘冲压件被设计出来以容纳电池或压缩天然气储存容器。

互联网摘选

5、

Computer Aided Analysis and Design on Structural Parts of Truck Chassis; Research on Computer Aided Forming Process Design of Composed Material Structure

载重汽车底盘结构件的计算机辅助分析与设计复合材料构件计算机辅助成型工艺设计的研究

互联网摘选

6、

Electrophoretic Painting of Automotive Chassis Weldment

汽车底盘焊接件的电泳涂装工艺

互联网摘选

7、

Research on Application of TRIP Steel in Chassis Structure

TRIP钢在汽车底盘结构件中的应用

互联网摘选

8、

Application of Corrosion Resistant Epoxy Impregnating Varnish in Motorcar Chassis

高耐蚀性环氧浸漆在汽车底盘件上的应用

互联网摘选

9、

At present, the company's leading product for Tatra ( TATRA) T815, T815-II type, Type III's long march chassis Series Mercedes-Benz parts and accessories, such as heavy vehicles.

目前，公司的主导产品为太脱拉（TATRA）T815、T815-II型、长征III型车的底盘件和奔驰系列等重型汽车配件。

互联网摘选

10、

A mathematical model is set up for life consumption of the high temperture parts in aero-engine.

在航空发动机热端件寿命消耗模型中考虑了离心负荷、热负荷及蠕变的影响。

互联网摘选

11、

Protective Coating of Modified Silicon Sol on the surface of Magnesium Alloy in Aircraft Engine

发动机镁合金件改性硅溶胶防护涂层的研究

互联网摘选

12、

Application of the Feature Modeling in the Parametric Design of the Typical Structures of Aeroengine

特征建模技术在航空发动机典型结构件参数化设计中的应用

互联网摘选

13、

Push wiring harness into the bonnet reinforcement.

将线束推入发动机舱盖加强件。

provided by jukuu

14、

The Optimal Design of the Moving Bar Lengths in Swing Piston Engine

摆动活塞发动机运动杆件长度的优化设计

互联网摘选

15、

A computational model for life consumption and life monitoring of Aeroengine

某航空发动机热端件寿命消耗计算模型及寿命监视

互联网摘选

16、

Three-dimensional elastoplastic finite element analysis of the back-joint subassembly of SRM

固体火箭发动机接头组合件三维弹塑性有限元分析

互联网摘选

17、

Based on object oriented BP network, a software prototype of scheme selection of aeroengine rotor coupling is developed in Visual C++ 6.0 development environment. An example is adopted to validate the rationality of this method.

基于面向对象的BP网络模型，在Visual c++6.0的开发环境中实现了航空发动机转子连接件方案选择的软件原型，并用实例进行了验证。

互联网摘选

18、

Finally, the paper by analysis the step bar and engine cylinder head specimen variable energy scan imaging detection data to verify the feasibility and effectiveness of the variable energy X-ray detection method.

最后，论文通过对阶梯试块和发动机缸盖试件的变能量扫描成像检测试验数据的分析，验证了变能量扫描X射线检测方法的可行性和有效性。

互联网摘选

19、

Firstly, the monitoring status quo of the lube oil consumption rate which reflects the wear state of the rotating parts of the aero-engine is analyzed, a method of forewarning the superscale of the lube oil consumption rate by forecasting the consumption rate is presented.

首先分析反映航空发动机转动件磨损状况的滑油消耗率监控现状及其不足，提出通过对滑油消耗率预测以预警滑油消耗率超标的方法。

互联网摘选

20、

A method which is applied to measure the surface temperature of the aeroengine rotor parts by using the thermoscope-piece to accomplish static state temperature measurement for a certain aeroengine compress rotor blade is introduced.

介绍了一种应用于航空发动机旋转件表面的温度测量方法，即使用测温片完成某航空发动机压气机转子叶片的稳态温度测试。

互联网摘选