In the production process of tire cord steel, total oxygen and inclusion composition is controlled by using Si-Mn alloy and changing refining slag. The inclusion morphology is improved greatly.

1、

Main equipments and operation schedule for producing tire cord steel in Shagang are described.

介绍了沙钢生产帘线钢的主要设备及工艺操作规程。

互联网摘选

2、

Quality of tire core steel out of CC bloom

连铸轮胎钢丝钢的质量

互联网摘选

3、

Structure design and processing technology of large forest tire with steel breaker

大型钢丝缓冲层林业轮胎的结构设计及生产工艺

互联网摘选

4、

Thermodynamics of Deoxidation Equilibrium of CaO-Al_2O_3-SiO_2 Slag for Producing Tire Steel

CaO-Al2O3-SiO2三元渣对硬线钢的脱氧热力学计算

互联网摘选

5、

The results showed that the performance of the tire with the low shrinkage nylon cord was similar to that of the post-cure inflated tire.

初步结果表明：采用此法后，轮胎的各项性能均与现生产的尼龙后充气轮胎基本相同或相近。

互联网摘选

6、

Removing Post-cure inflation of Bias Tire by Using Low Shrinkage Nylon Cord

斜交轮胎应用低收缩尼龙帘线取消硫化后充气

互联网摘选

7、

It was found that the improper parameters in building, dimensions of extrudates, overall circumference of green tire and pressure in shaping as well as the deviations in calendering, extruding, building and curing processes might cause the cord bending in tire shoulder.

成型参数、挤出半成品尺寸、胎坯外周长和定型压力不当以及生产过程中的压延、挤出、成型、硫化工序出现偏差均会造成肩部帘线弯曲质量缺陷。

互联网摘选

8、

With respect to the tire with longitudinal grooves, the temperature in tire crown and shoulder decreases obviously, but the temperature in tire side and bead changes slightly.

同时，与无花纹轮胎相比，含纵向花纹轮胎的胎肩、胎冠部的温度显著降低，而胎侧、胎圈部的温度变化很小。

互联网摘选

9、

With the decrease of aspect ratio, the temperature in tire shoulder and crown decreases obviously, and the temperature in tire side and bead hardly change.

结果还表明，轮胎胎肩、胎冠部的温度随扁平率的减小而有所降低，而胎侧、胎圈部的温度则几乎没有变化。

互联网摘选

10、

Causes and countermeasures for cord bending in BTR tire shoulder

全钢载重子午线轮胎肩部帘线弯曲原因分析及解决措施

互联网摘选

11、

Analyzing the Reason of Tire Shoulder on an Aberrant Course

轮胎胎肩脱空原因分析

互联网摘选

12、

Tire shoulder temperature increases significantly with the increase of belt angle.

带束层施工参数虽对轮胎最高温度影响不大，但随着带束层角度的增加胎肩温度增加明显。

互联网摘选

13、

Tire road contact pressure distribution and cornering performance is concluded. 6. The combined pattern tire dynamic rolling at70km/ h speed in a horizontal road is simulated in ABAQUS/ Explicit.

得出了接地压力分布情况及侧偏性能。6.在ABAQUS/Explicit中模拟了组合花纹轮胎在水平路面上以70km/h速度动态滚动的情况。

互联网摘选

14、

In this paper, the design of a tire pressure monitoring and alarming system is presented, utilizing the linear relationship between tire pressure and rolling radius.

利用轮胎气压与滚动半径之间的线性关系，提出了一种轮胎气压监测与报警系统。

互联网摘选

15、

This article derived the relations of tire deformation stress and strain through the analysis of the force when the tire rolling, establishing a mathematical model of the tire temperature rise mechanism on this basis.

本文通过分析轮胎滚动时的受力情况，对轮胎变形的应力与应变关系进行推导，在此基础上建立轮胎温升机理的数学模型。

互联网摘选

16、

The current study is of very positive significance for the optimization of the tire structure, prediction of tire rolling resistance, and promotion of low rolling resistance and green tires.

本课题研究成果对于优化轮胎设计、预测降低滚动阻力的方向、推动绿色轮胎的发展有着非常积极的意义。

互联网摘选

17、

Because radial tire has the small rolling resistance, large load capacity and many other advantages, so it is used more and more widely.

子午线轮胎因为有滚动阻力小以及负荷能力大等诸多优点，所以使用越来越广泛。

互联网摘选

18、

Finally, the steady tire temperature field and rolling resistance under different working conditions are calculated based on the direct solving strategy.

基于直接策略，分析计算了不同工况下的轮胎稳态温度场和滚动阻力。

互联网摘选

19、

The influence of five parameters which include speed, inflation pressure, vertical load, crown compound elastic modulus and belt angle to tire steady state rolling resistance was mainly studied.

着重研究了轮胎行驶速度、充气压力、垂直载荷、胎冠胶弹性模量、带束层帘线角度五个参数对轮胎稳态滚动阻力的影响。

互联网摘选

20、

FEA of belt deformation of radial tire on camber rolling state

侧倾滚动轮胎带束层受力状态有限元分析

互联网摘选