The amplitude of the fluctuation a has an important effect on interface morphology, when appropriate value is assigned to a, noise can enhance the emergence of side-branches, and form cellular dendrites, the tip velocity must be influenced at the same time;

The anisotropy is smaller, smaller the tip velocity is, the side-branches are prone to grow, and form cellular dendrites;

各向异性系数γ越小，尖端生长速度越小，越易于侧向分支的生长，形成胞状枝晶；

互联网摘选

The results indicate that, with increase in undercooling, a small nuclei will grow developed dendritic, the tip velocity at steady state is become faster;

结果表明，随着过冷度值的增加，晶核由一圆核逐渐发展为发达的枝晶，相应的枝晶稳态尖端速度明显加快；

互联网摘选

The simulation jet tip velocity with reverse initiation is 8.78 km/ s, while with normal initiation it is only 4.86 km/ s.

计算的逆向起爆形成射流头部速度为8.78km/s，而正向起爆形成的射流头部速度为4.86km/s。

互联网摘选

With increasing in the environment density, the spray penetration and spray tip velocity decrease more rapidly, and the spray angle becomes larger.

环境密度增大时，喷雾破碎期缩短，贯穿距减小、锥角增大；

互联网摘选

It is a very important approach to increase the tip velocity of rotor for the high pressure ratio.

提高单级压比的重要途径之一，就是提高动叶的叶尖速度，这同时就会造成叶尖的超音速。

互联网摘选

Tip clearance of the turbine plays an important role on the aeroengine performance. Dimension conversion from hot state to cold state of the turbine components is an important content of tip clearance research.

涡轮叶尖间隙影响着发动机的性能，涡轮典型部件的冷热态尺寸换算是间隙设计的重要内容。

互联网摘选

The results show that the parameters chosen are reasonable and the tip vanes on wind turbine blade improve the start performance and obviously enlarge the working range of the unit.

试验表明：机组的总体参数选择合理，叶片上的小翼对改善机组低风速下的起动性能和加大全机工作范围有明显好处。

互联网摘选

A commercial N-S solver has been employed for simulation and investigation of the unsteady flow field inside the tip clearance of a turbine rotor.

商用N S求解器已经被用于透平动叶顶部空隙的非定常流场的模拟和研究。

互联网摘选

Counter rotating turbine Effects of endwall relative motion on tip clearance flow in turbine rotors

正反转双转子涡轮机机匣相对转动对涡轮叶顶间隙流动的影响

互联网摘选

A model for estimating tip clearances in gas turbine engine transients

燃气轮机过渡过程中叶尖间隙估算及间隙变化对加速过程的影响

互联网摘选

Contrasts and analyses of flow fields in turbine stage with different slotting types are made to investigate the impact of slot at rotor tip on the turbine efficiency and secondary flow loss.

本文对几种形式开槽的涡轮级流场进行了对比分析，分析了动叶顶部开槽对涡轮级效率和二次流损失的影响。

互联网摘选

The flow near the tip region and heat transfer characteristics of the blade was analyzed. Numerical results showed that the blade can be well protected by the air-cooled configurations.

对具有复杂冷却结构的原型空气冷却动叶进行了整体气热耦合计算，分析了叶片叶顶附近的流动和叶片的换热特性，表明原型气冷结构基本能够为该叶片提供较好的保护。

互联网摘选

Effects of squealer tips on blade aerodynamic performances and tip heat transfer in a gas turbine were investigated.

应用数值方法研究了燃气透平动叶顶部凹槽对动叶气动性能及叶顶传热的影响。

互联网摘选

Mechanical model for atomic force microscopy tip sliding on the surface of sample

原子力显微镜针尖在试样表面滑动的力学模型

互联网摘选

The aim of this dissertation is to make theoretical analysis and experimental research on the field emission current generated between tip and sample surface, analyzing the effect of fabrication parameters on the results of weak current during the process of dots and lines fabrication.

本课题对AFM电场诱导氧化加工中探针与样品之间产生的场发射电流进行了理论分析和实验研究，通过实验分析了加工参数对氧化点、氧化线加工过程中检测出的微弱电流的影响。

互联网摘选

And when the indenter tip touched the surface of the sample, the trend of the displacement values measured by the sensor would depart from that of the displacement values of indenter having no load.

而当压头尖与试样表面接触后，压头与试样之间将产生作用力，使电容测微仪的测量值偏离加载装置空载下的输出曲线趋势。

互联网摘选

Scratch process may be divided into three phases, i.e. a stylus tip indenting coating surface, the stylus tip slipping on coating surface and the stylus tip rising over coating surface.

划痕过程可以分为划针尖端压入涂层表面、划针在涂层表面上滑动和划针升高等三个阶段。

互联网摘选

In the measurement process the AFM feedback controller make the scanner move the sample along z-axis and keep the vdW force between the tip and sample surface constant.

在测量过程中，AFM反馈控制器控制扫描器沿z轴移动样本，保持针尖-样本表面间的vdW力恒定。

互联网摘选

Before the indenter tip touched the surface of the sample, the displacement value measured by a capacitive displacement sensor was the output of the loading mechanism without load.

在压头尖与试样表面接触前，由电容测微仪测得的位移值是加载装置空载下的输出值；

互联网摘选

When the operating force of interaction between AFM tip and the surface of liposome are beyond critical values, the liposomes rupture into bilayers.

当AFM的探针与脂质体表面相互作用力超过某临界值时，脂质体胞囊破裂，变成脂双层结构。

互联网摘选