Laser scanning measurement for high temperature deformation of materials

1、

A Study on Precipitation Induced by High Temperature Deformation of High-Speed Steel

高速钢高温形变诱发析出的研究

互联网摘选

2、

Temperature deformation control in cantilever construction of box girder bridge

大跨度预应力混凝土箱形梁桥悬臂施工中温度变形控制

互联网摘选

3、

These defects have a relation with the die temperature. Stabilizing the die temperature can reduce the defect.

这些缺陷跟模具的温度有关，稳定铸模的温度可以减少缺陷的产生。

互联网摘选

4、

The numerical simulation of temperature field and shrinkage defect prediction for a valve casting, which was involved in 4 kinds of casting processes, were carried out. The good agreement has been obtained between the numerical simulation and the experimental result verification.

对采用4种不同铸造工艺方案的阀体铸件凝固过程进行了数值模拟及缺陷预测，获得了与试验相一致的模拟结果。

互联网摘选

5、

It has analyzed filling behavior, temperature field changing and defect that might produce and improved the technology utilized the analysis result then received the more ideal simulation result.

对铸件充型过程、温度场变化及所产生的缺陷进行了分析，依据分析结果对工艺进行了改进，最终实现较为理想的模拟结果。

互联网摘选

6、

Quantitative Diagnosis to Internal Temperature and Inner Defect of the Hollow Cylinder-shaped Heat Equipment by Using Infrared Technique

红外测温对圆筒设备内部温度及内壁缺陷的定量检测

互联网摘选

7、

Study on the influence of substance temperature on the defect and optical performance of single YbF_3 films

基底温度对YbF3薄膜缺陷和光学性能影响研究

互联网摘选

8、

Temperature Distribution of Defect Surface and Effect of Natural Convection on Thermographic Inspection

缺陷表面温度分布及空腔自然对流对红外检测的影响

互联网摘选

9、

Numerical Simulation of Temperature Distribution and Defect Prediction for Working Table Casting

工作台铸件温度场数值模拟及缺陷预测

互联网摘选

10、

Study on High Temperature Defect Structure of ( CoMgNi) O

（CoMgNi）O系材料的高温缺陷研究

互联网摘选

11、

Through water pressure test, ammonia leakage test and field high temperature melted salt cycle test, it is shown that the tube joint welding quality meets completely the design and process demands.

经水压试验、氨渗漏检验及现场高温热熔盐循环试验，焊接接头质量完全达到设计及工艺要求。

互联网摘选

12、

High Temperature Low Cycle Fatigue Life Prediction Models

高温低周疲劳寿命预测模型

互联网摘选

13、

Experimental procedure and data processing of pipe material for high temperature low cycle fatigue

管材高温低周疲劳实验方法及数据处理

互联网摘选

14、

Solving some thermodynamic problems related to temperature with cycle procedure means

用循环过程法求解某些与温度有关的热力学问题

互联网摘选

15、

Discussion of the Evaluating Criterion of High Temperature Low Cycle Fatigue

高温低周疲劳寿命评价准则的探讨

互联网摘选

16、

Carry on temperature cycle test on typical components, inspects solder joint crack in different cycle, observe microstructure of solder joint in virtue of metallographic analyse, study solder joint failure mode in temperature cycle and offer basis to improve technology parameter.

针对典型元器件进行温度循环试验，在不同的循环周期检查焊点的开裂情况，并采用金相分析观察焊点的显微组织，分析焊点在温度循环条件下的失效模式，为改进工艺参数提供依据。

互联网摘选

17、

The coefficient of performance of R290/ CO_2 cascaded refrigeration cycle can be enhanced by using rotary compressor without suction and discharge valves and by replacing throttle with expander in CO_2 low temperature cycle.

在CO2循环中可利用无吸排气阀的回转式压缩机，用膨胀机代替节流阀，以提高R290/CO2复叠式制冷循环的性能系数。

互联网摘选

18、

After evaporator frosted, frost temperature cycle minimum value rea-ched setting lower limits and cold storage could not operate within the scope, then the cooling efficiency of the evaporator was decreased. 2.

结霜后的霜温周期最低值达到霜温设定下限，蒸发器的制冷效率下降。

互联网摘选

19、

Firstly, it has no need to recheck or retighten, so it can avoid loosen of connection point caused by perturbed temperature cycle and wire fracture.

首先，使用过程中它不需要重新检查或拧紧，可以有效的避免因扰动温度循环、绞线断裂等造成的接触点松动。

互联网摘选

20、

High-low temperature cycle lifetime of 1310 nm LD modules was studied by experiment under different simulation environmental conditions. A mathematical model of the cycle lifetime of laser diode was established.

模拟了在不同的环境条件下，对1310Nm LD组件进行了高低温循环寿命实验，建立了循环寿命的数学模型。

互联网摘选