gear tooth

Chamfering Process of Gear Tooth Profile Calculation and Drawing of Involute Part in Gear Profile Sample

齿轮倒棱工艺渐开线齿形样本中渐开线部分的计算与绘制

互联网摘选

Sliding ratio is an important index which can evaluate the wear of spherical gear tooth surface.

采用滑动系数作为衡量球齿轮齿面滑动磨损程度的重要指标。

互联网摘选

For gear drive, lubricant film between tooth surfaces is important to protect them from failure.

在齿轮传动中, 齿面间润滑油膜的存在及其厚度对防止齿面失效具有重要意义.

网络文摘精选

Ausform finishing process for hardened gears and study on gear tooth deformation theory

硬齿面齿轮精密热滚挤工艺及轮齿变形的研究

互联网摘选

contact stress analysis of a spur gear tooth by using boundary elemental method

应用边界元方法的正齿轮接触应力分析

互联网摘选

When designing gear hob, worm gear hob and shaping milling cutter, it should be verified whether the interfere would occur between grinding wheel and the next gear tooth on condition of pledging the relief grinding length of the back of tooth.

在设计齿轮滚刀、蜗轮滚刀和成形铣刀时，要校验在保证齿背铲磨长度的情况下，所用砂轮是否和下一个齿发生干涉。

互联网摘选

Deviation of Addendum Circle and Its Influence on Thickness Measurement of Gear-tooth

齿顶圆偏差对齿厚测量的影响及修正

互联网摘选

Study on modification technique of hourglass worm gear tooth surface

小柱面包络环面蜗杆齿面修形方法研究

互联网摘选

An optimum modification of the cycloid gear tooth

摆线轮齿形修整的优化

互联网摘选

The tooth root stress of cylindrical gear has been calculated and analyzed in detail, and compared with the result obtained by the load bearing capacity computing method of cylindrical gear ( GB3480 83).

对圆柱齿轮的齿根应力进行了大量的计算和详细的分析，并且与按国标渐开线圆柱齿轮承载能力计算方法（GB3480－83）计算的结果进行了对比。

互联网摘选

The Computer Simulation Technology of the Hourglass Worm Gear Tooth Meshing Line

环面蜗杆齿面啮合线的计算机仿真技术

互联网摘选

If either the number of sun or ring gear is not multiple of planet gear, system will run effectively, with lower impaction of tooth mesh in and out.

行星轮与内齿圈齿数不为行星轮个数的整数被时，轮齿的啮入、啮出对系统的冲击小，系统的效率高。

互联网摘选

Theoretical analysis of tooth strength of cycloid-gear reducer

摆线针轮减速器齿廓强度理论分析

互联网摘选

Determining the optimum tooth number when measuring the base tangent length of an involute gear

渐开线齿轮公法线长度测量最佳跨测齿数的确定

互联网摘选

Minimum Teeth of No-undercut Standard Gear with Arcuate Tooth Traces

标准圆弧齿线圆柱齿轮不发生根切的最少齿数

互联网摘选

Establishment of theoretical equation for the tooth flank of non-involute gear-shaper cutter

非渐开线插齿刀齿侧面理论方程的建立

互联网摘选

Polar milling tooth for milling machine is developed by the large gear tooth new milling machine.

极坐标铣齿机床是针对铣削大型齿轮所开发的新型铣齿机床.

互联网摘选

Study of Virtual Simulation of Grinding of Digital Gear Tooth Surface

数字化齿面磨削加工虚拟仿真研究

互联网摘选

The Comparative Study of the Bending Stress and Elastic Deformation Calculation of Gear tooth

齿根应力与轮齿弹性变形的计算方法进展与比较研究

互联网摘选

Double circular arc spiral bevel gear is applied to heavy truck drive axle of the need for bearing capacity and dynamic characteristics of two aspects of research, its bearing capacity in the coal mine scraper conveyer reducer of circular arc tooth profile has been verified.

双圆弧弧齿锥齿轮应用到重卡驱动桥中需要对承载能力和动态特性两方面进行研究，其承载能力在煤矿刮板输送机圆弧齿廓减速器研究中已经得到了验证。

互联网摘选

Gear tooth tip relief based on standard hob

基于标准齿轮滚刀的齿顶修缘

互联网摘选

This paper proposes a new method to modify the cycloid gear tooth of reducer in order to improve the gear engagement.

本文以改善摆线针轮减速器轮齿啮合质量为目的，提出了一种新颖的摆线轮齿形修整方式。

互联网摘选

Calculation of Pressure Angle and Spiral Angle on Spiral Bevel Gear Tooth Surface

螺旋伞齿轮齿面上指定点处压力角及螺旋角的计算

互联网摘选

These works summer up the common grounds of various gear tooth forms, so they will b.

上述内容是各种纯滚齿形共同点的总结,是研究纯滚齿轮的基础.

互联网摘选

Method for eliminating 3-shaped contact zone on gear tooth profile

齿轮之字形接触区的消除方法

互联网摘选

A Proof of Thinned Addendum Thickness of a Gear Tooth Generated with Positive Correction

正变位齿轮齿顶厚度必变小的证明

互联网摘选

Chamfering Process of Gear Tooth Profile

齿轮倒棱工艺

互联网摘选

Through the Sliding Ratio to reflect the points of the gear tooth surface in gear meshing process. 2.

通过该系数来反映齿轮在啮合过程中齿面各点的接触情况。

互联网摘选

The Fracture Process Simulation and Fracture Strength of Gear Tooth in Mining Machine

采掘机械齿轮轮齿断裂过程仿真与断裂强度

互联网摘选

A Calculation of Bulk Temperature and Thermal Deflection of Gear Tooth about Profile Modification

齿轮本体温度场和热变形修形计算

互联网摘选