crank shaft

Optimized of parameters of basic dimensions of double crank shaft mechanism

双曲柄机构基本尺寸参数的优化

互联网摘选

The main products are sprocket for motorcycle ( vehicle ) and crank-shaft for general machinery.

目前生产销售的两大类产品为传动 链轮 和通用汽油机曲轴.

互联网摘选

Site Repairing Method for Type 300 Diesel Engine after Burning out of Crank shaft Bearing Liner

300型柴油机曲轴烧瓦后的现场修复方法

互联网摘选

The tentative calculational methods is used in the design of crank shaft balancer, the workload of which is very large.

在进行活塞式压缩机设计时，关于曲轴平衡块的设计计算大多采用试算法，计算量比较大。

互联网摘选

And in fact be able to add speed, but also directly driven by the crank shaft.

而实际上能够加减速, 还可由曲柄轴直接驱动.

互联网摘选

The finite-element method for the stress analysis of crank shaft

曲轴应力分析的有限元方法

互联网摘选

To solve the poor economic and dynamic performance at high engine speed, a new crank shaft mechanism of air powered engine was proposed.

为解决高转速下动力与经济性能的下降，提出一种新的气动发动机曲轴连杆机构。

互联网摘选

Measuring deflection of crank shaft of M. E. before starting up ( after sea trial ).

主机动车前 ( 航行试验后 ) 曲轴甩档测量.

互联网摘选

This paper describes the distribution of surface hardened layer and analyses of the residual stress in the nodular graphite cast iron crank shaft with its Journal and arm corner hardened simultaneously by high frequency induction heating.

本文叙述了对球墨铸铁曲轴轴颈与园角部位同时高频淬火后获得的硬化层分布，以及硬化层中残余应力分析。

互联网摘选

based on the review of the existing silk looms in our country, the reconstruction of rollingup mechanism, back beam height, machine depth, angle disc of crank shaft, and right or left type of the machine is discussed.

本文在介绍我国现有丝织机的基础上，对丝织机改造中有关卷取机构、胸后梁高低、机身长短、曲轴回转角度盘和左右手机型等问题进行了讨论。

互联网摘选

A high-efficiency high-precision new crank-shaft grinding method , the process-centralized method, is described.

介绍了一种高效、高精度曲轴 磨削加工 的新方法──工序集中式曲轴磨削加工法.

互联网摘选

The piston is connected to the crank shaft by a connecting rod.

活塞通过连接杠连接到曲轴.

互联网摘选

Every bike has a serial number near the crank shaft.

每辆自行车在曲柄轴附近都有一个序列号.

网络文摘精选

A low cost microcomputer closed loop control system of crank shaft processing

经济型微机闭环曲轴加工控制系统的研制

互联网摘选

With the third steps and the fourth steps natural frequency vibration, the smaller close to the second crank arm of crankshaft and round place natural frequency of the main shaft transition the position is.

以第3阶和第4阶固有频率振动，位置越靠近曲轴第二个曲柄臂与主轴过渡圆处固有频率越小。

互联网摘选

Design of vibration table in the dynamic equilibrium detection system of crank shaft component

曲轴组件动平衡检测系统中振动台设计

互联网摘选

Finding involved inadequate corrective actions to prevent repeat failure of the number nine main crank shaft bearing on emergency diesel generator number one.

发现物涉及到不充分的，纠正措施，用来避免重复的失效，那是关于，9号大曲柄轴，在第一号柴油机。

互联网摘选

Failure analysis of crank shaft box of tri-plunger HP pump and its improvement

三柱塞高压泵曲轴箱故障原因分析及技改

互联网摘选