pump bracket的例句大全

Simulation Analysis of Fatigue Life of Fuel Pump Bracket Under Random Load

随机载荷下燃油泵托架疲劳寿命仿真分析

互联网摘选

based on the analysis results, the paper gives a structure modify scheme, and the new fuel pump bracket has succeeded in the random vibration test.

并在此基础上提出改进方案，改进后的油泵托架成功地通过了随机振动试验。

互联网摘选

Loosen the accessory drive belt at the power steering pump bracket, if equipped or at the idler pulley bracket ( refer to Group 7, Cooling System for the proper procedure).

如果装备且在惰轮皮带盘托架上，放松动力转向泵托架上的附件驱动皮带。

互联网摘选

Using numerical simulation technology, we study a method for predicting the structural fatigue life of a fuel pump bracket ( FPB) that contains rubber cushion for vibration reduction.

针对一类含橡胶减振垫燃油泵托架出现疲劳断裂的现象，研究利用数值仿真技术预测结构疲劳寿命的方法。

互联网摘选

Some type of oil spout pump bracket can not be produced in our factory now.

另外我厂一些型号的喷油泵支架目前还无法生产。

互联网摘选

According to the production, this paper analyzed the causes of the crack in the body cylinder and the porosity in the oil pump bracket, then, some efficient methods of solving these problems were given.

本文从生产实践分析汽缸体缸筒裂纹和机油泵支架处气孔的形成原因，通过采用调整砂芯排气孔位置等一系列工艺措施，有效解决了汽缸体缸筒裂纹及喷油泵支架处气孔问题。

互联网摘选

the top end bracket shall be fitted with a lifting bail and shall be capable of supporting four ( 4) times the combined weight of the pump and motor.

顶部尾轴承架应该配置吊环，应该能够支撑泵和电机的总重量四（4）倍的压力。

互联网摘选

pw, pwf mainly by the pump cover, pump casing, impeller, shaft seal, shaft, and bracket the composition of such components.

PWF主要由泵盖、泵壳、叶轮、轴封、轴、和托架等零部件组成。

互联网摘选

Casting for auto parts ( calliper, bracket, disc, pressure plate etc ), reerigerator and air conditioner compressor parts ( cylinders, crankshaft etc ), machinicalparts, construction parts , motorparts, pump parts etc.

汽车用铸件 ( 制动钳体 、 支架 、 制动盘 、 压盘等 ), 机械零件,冰箱、空调压缩机铸件 ( 缸体 、 曲轴等 ), 建筑工程用铸件, 电机零件, 水泵等.

网络文摘精选

If equipped, attach the power steering pump and bracket.

如果配备, 连接动力转向泵和支架.

网络文摘精选

pump-boards fixed with bolts directly in the bracket.

泵体护板用螺栓直接固定在支架上.

互联网摘选

the punching die design of external bracket of car pump is elaborated.

详细论述了轿车油泵外用支架的冲压模具设计过程.

互联网摘选

Clip the pump into the bracket.

将泵卡入支架。

provided by jukuu

Press pump out of the bracket at the rubber mounts.

从橡胶支座处将泵从支架中按出。

provided by jukuu

Development of electro-hydraulic unloading and supervisory control system of emulsion pump aims at controlling the unloading of emulsion pump, and supervising and controlling emulsion pump parameters, and ensuring the hydraulic pressure bracket system works without accident.

研制乳化液泵电液卸载及监控系统旨在控制乳化液泵的卸载，监控乳化液泵站工作的关键参数，以确保液压支架系统正常安全工作。

互联网摘选

Analysis and Repair for Breaking Cause of Boom Bracket Eared Plate of Import Concrete Pump-mounted truck

进口混凝土泵车臂架耳板断裂的原因解析及修理

互联网摘选

The holding claw must engage in the cut-out on the bracket for the high-pressure pump.

固定爪必须在高压泵支架上的切口中接合。

provided by jukuu