plastic slip的例句大全

ImproVement of The Method for Determining The Direction of Plastic Slip Line

确定塑性平面应变滑移场方向的一个简便方法

互联网摘选

Solutions for the Plastic Slip Line Fields Around Elliptical Holes in Perfectly Plastic Materials

理想塑性材料中椭圆孔附近的塑性滑移线场解

互联网摘选

The effect of tilt angles and angular displacement on many key parameters of fretting such as contact pressure, relative slip distance, dynamic curves, plastic accumulated strain and contact status is investigated in details.

分别研究了不同倾斜角与角位移幅值对接触应力、相对滑移量、动力学曲线、塑性应变和接触状态等微动摩擦学关键参数的影响规律，并结合实验数据，对模型的模拟结果进行验证。

互联网摘选

The dislocation slip and twinning are the modes of plastic deformation during the hard-drawn.

冷拔过程的塑性变形为孪生和滑移，孪生为主要变形机制；

互联网摘选

Long range and short range frictional slip-lines on plane contact surface in plastic compression ( the rule of isoclinic gradient)

塑压接触平面上之长程滑动与短程滑动（等倾陡线规律）

互联网摘选

Analysis of elastic-plastic finite element for two dimension slope slip surface and stability

二维边坡滑动面及稳定性弹塑性有限元分析

互联网摘选

By using the characteristics of plastic deformation the field of slip band is given in this paper. Stress can be derived from geometric features of slip band.

本文利用塑性变形过程的特点，建立了滑移线场，由滑移线的几何性质来确定应力分力。

互联网摘选

Stress calculation of single crystal under finite slip plastic deformation

单晶体塑性滑移有限变形下的应力计算

互联网摘选

The distribution characteristics of stress, strain and stored energy has been analysis, and the slip system during plastic deformation has been discussed.

讨论了应力、应变场和形变储存能分布的特点，并讨论了滑移系在塑性变形过程中的开动情况。

互联网摘选

Based on the theory of slip line and plastic deformation of metal, the clamping force for forging reduction of cylinder is analyzed and studied.

应用滑移线理论和金属的塑性变形理论，分析研究圆柱体镦粗过程中的夹紧力的计算方法，并与试验结果进行比较。

互联网摘选

In consideration on the on-line R-value measurement of aluminum deep drawing sheets, the selection of initial slip systems was analyzed according to the activation process of the slip systems during plastic deformation. Initial R values of the 3104 aluminum sheet in different directions were calculated.

以深冲铝板R值的在线检测为应用背景，塑性变形滑移系开动的过程为出发点，分析了初始滑移系选取的方式，并计算了不同取向3104铝合金板的初始R值。

互联网摘选

The face-centered cubic ( f.c.c.) crystals with high stacking fault energies deform predominantly by crystallographic slip. For the crystals with low stacking fault energies, in addition to crystallographic slip, deformation twinning also plays an important role in maintaining generalized plastic flow.

高层错能FCC材料塑性变形主要靠晶体滑移，而对于低层错能材料，除晶体滑移之外，在维持正常塑性流动方面，变形孪晶也起重要作用。

互联网摘选

Roughness on the metal specimen polished surface will be induced when it yields plastic deform or fatigue damage for its interior microscopic crystal grain slip dislocation, and this is very different when it yields elastic deform.

与仅仅承受弹性变形时不同，当金属试件承受塑性变形或发生疲劳损伤时，内部微观晶粒滑移位错等会导致表面粗糙化。

互联网摘选

Here, according to the classical theory of plastic deformation of the single crystal and slip characteristic of the face centered cubic with zincblende structure crystal, the reasons why the polygons came into being were clarified. The polygons'internal angle must be 60 ° or 120 °.

文中从经典的晶体范性形变理论和面心立方闪锌矿结构晶体所具有的滑移特性出发，阐明了出现在CZT（111）Cd面的多边形的形成机理，其内角必为60°或120°。

互联网摘选

Research on stress equation in slip line field of axisymmetrical plastic deformation

轴对称塑性变形滑移线场应力方程研究探讨

互联网摘选

Solutions of some plastic plain strain problems based on unified strength theory and unified slip line field theory

用统一强度理论和统一滑移线场理论求解某些塑性平面应变问题

互联网摘选

Discussion on velocity solution of slip line theory for geotechnical materials& the application of generalized plastic theory

关于岩土材料滑移线理论中速度解的讨论&广义塑性理论的应用

互联网摘选

The effects of the slip plane orientation and load on dislocation emission or plastic zone have been investigated.

考察了滑移面取向、外荷对发射位错及塑性区的影响。

互联网摘选

The result also reveals that the reinforcement material penetrating into the plastic zone of the slope will effectively elevate the slip resistance effect.

同时，计算分析了加筋材料摆放位置不同时，对土坡抗滑能力的影响效果。提出当将加筋材料贯穿于土中塑性区时，加筋效果最明显。

互联网摘选

A Method of Confirming Plastic Section of Workpiece Based on the Slip-line Field Theory

用滑移线理论确定工件塑性区的一种方法

互联网摘选