1、

The recrystallization textures consist of cube orientation rotated by 20 ° round normal direction ( ND) and { 011} 〈 122 〉 orientation for samples overaged and then cold rolled.

冷轧前进行过时效处理,其再结晶织构主要由绕法向旋转了20°的立方取向(Cube+ND20)和{011}〈122〉取向构成;

互联网摘选

3、

geometry analysis method for normal direction clearance calculation about internal gearing involute gear transmission

内啮合渐开线齿轮传动法隙计算的几何分析法

互联网摘选

4、

Considerable residual stresses exist in the normal direction.

在其厚度方向存在着可观的残余应力.

词典精选例句

5、

The results show that the emission direction of the hot electrons at the rear side of the target shifts towards the target normal direction as the target thickness increases.

实验发现,随着靶厚度的增加,靶后超热电子的发射方向向靶的法线方向移动,同时电子束的发散角变大。

互联网摘选

6、

And the motions in the normal direction and the tangent direction of the wheels were researched and the kinematic equations and the nonholonomic kinematic state space used in the acceleration control were obtained.

重点研究滚轮的法向和切向运动,建立了机器人运动学方程和无奇异性的非完整运动学状态空间。

互联网摘选

7、

The unsteady state term was discretized using the full implicitly schemes. For the diffusion terms, the normal direction vector ( the first diffusion) and the tangent direction vector ( the second diffusion) were calculated by using the intersectant and iterative algorithm.

对于非稳态项采用全隐格式,对于扩散项,采用法向扩散项(一次扩散项)和切向扩散(二次扩散项)进行相互交叉迭代的算法。

互联网摘选

8、

the normal direction error of the approximation plane cubic curve with biarc

平面三次曲线的双圆弧逼近的法向误差

互联网摘选

9、

The center of the circumcircle corresponding to the triangle formed by the three selected points is just the circle center of the compact, and the normal direction of the triangle plane determines the angle of the cutter teeth.

这3个测点构成1个三角形,三角形对应的外接圆圆心就是复合片圆心,三角形所在平面的法线方向决定了切削齿的角度。

互联网摘选

10、

When Zircaloy-4 plate is rolled at high a tempera-ture, { 10` 11}` 2113 and { 11` 21}` 2113 slips are the basic deformation systems, thus the operations of them make basal pole orientate along the normal direction of plate.

Zr-4合金板在a相高温区轧制时,{10`11}`2113和{11`21}`2113锥面滑移是主要的形变系统,所以轧制后形成基极取向集中于轧面法向的织构。

互联网摘选

11、

The regularity of the residual _ stress changing along length and normal direction of interface derived model.

得到层内应力沿长度方向和界面法线方向分布的变化规律.

互联网摘选

12、

An algorithm of point in polygon testing based on normal direction is presented.

提出了基于法线方向的点包容检测算法.

互联网摘选

13、

Computational Formula for Induced Normal Curvature of Two Conjugate Tooth Surfaces along Normal Direction of Contact Line

两共轭齿面沿接触线法向的诱导法曲率计算公式

互联网摘选

14、

the transmitting probe produces a pulse which causes a p-wave in the normal direction of the plane and a s-wave in its shear direction.

发射探头对岩块法向脉冲后产生纵波,同时在其垂直方向产生横波沿该平面的方向传播。

互联网摘选

15、

The workpiece is clamped on the rotating table, and the normal direction of the workpiece at a certain angle with the direction of polishing tool spindle by controlling the angle of precision swing table.

将工件固定在旋转工作台上,然后对摆台的角度进行控制,以此来确保研抛工具主轴方向和工件法线方向成一定角度。

互联网摘选

16、

Its dashed line represents the direction in which the maximum energy is radiated, that is the normal to the plane defining the cut of the hemisphere, pointing towards the dark side.

它的虚线代表最大能量发射的方向,正交于定义半球切面的方向,指向没有光线的一边。

互联网摘选

17、

A unit vector in the direction of the projection of normal to T.

沿着方向上的单位向量,与T垂直。

互联网摘选

18、

Plane wave has the overall direction, compared with the normal migration, the plane-wave imaging results can be comparable to, and has a high computational efficiency.

平面波具有全局方向性,相对逐炮偏移而言,平面波偏移成像的结果是可以与其相相比的,并有很高的计算效率。

互联网摘选

19、

Vehicles in bus lanes may be going faster than traffic in other lanes, and some bus lanes may be in the opposite direction to normal traffic.

在巴士的车辆,速度可能比在其他行车的车辆更快。有些巴士的行车方向,或与一般行车刚好相反。

provided by jukuu

20、

The angles between the normal line direction and the flow direction shows strong effect to the drag forces in the study, this dissertation puts forward a formula about interference factor of the angles.

论文研究还表明,当块体的法线方向与水流流向之间存在一定夹角时,得出水平拖曳力受夹角影响的拖曳力函数表达式。

互联网摘选

  • 今日热词
  • 热门搜索

英语网英语词典(dict.25820.com)为您提供在线翻译英语词典单词大全英译汉汉译英等英语服务!可按单词字数词义分类查询。支持lj:关键词格式查询例句。

用户反馈
请选择反馈类型(可多选):
您的联系方式:
反馈内容:
提交成功 小编会尽快处理
回到顶部
点击反馈