mould core的例句大全

Design of injection mould for combined type neck bush of spherical core of water faucet

水嘴组合球芯内衬套注射模设计

互联网摘选

design of the four-way pulled core mould for plastics parts of large boxes and covers

大型箱盖类塑料件四开模的设计

互联网摘选

application of double-stage linkage core-pulling mechanism to mould for low pressure casting

二级联动抽芯机构在低压铸造模具中的应用

互联网摘选

the influence of the interval between the roller and core mould to brute force spinning of toper

旋轮与芯模之间的间隙对锥形件强力旋压的影响

互联网摘选

structural design analysis of quadruple mould unloading hot core box heated by coal gas

煤气加热四开模热芯盒结构设计及要点分析

互联网摘选

stability control of big-diameter gbf hollow pipe mould for cast-in-place concrete hollow-core floor slab 800 mm in thickness

800mm厚现浇混凝土空心楼板大直径GBF空心管胎模的稳定性控制

互联网摘选

miduban mould pressing doors : miduoban a double-sided mould pressing shaped, hollow core doors, a single style, low grades.

密度板模压门：密度板一次双面模压成型，门芯空心，款式单一，档次低。

互联网摘选

stability control of big-diameter gbf hollow pipe mould for cast-in-place concrete hollow-core floor slab 800 mm in thickness

800mm厚现浇混凝土空心楼板大直径GBF空心管胎模的稳定性控制

互联网摘选

DP 2 、 D 4 are mainly used for ramming sand core of small mould in foundry practice , whereas.

D4型气动捣固机,主要用于铸造行业捣固砂芯或小砂型.

网络文摘精选

During intersectant mould-core forming in die-casting die, bending pin postponing core-drawing mechanism is designed.

铸件要采用交叉型芯成型, 设计了弯销延时抽芯机构.

互联网摘选

A Study on Alcohol-Base Ti Slag Coating Used for Cold-Setting Furan Resin Sand Mould ( Core) for Heavy Castings

大型铸铁件呋喃树脂自硬砂型（芯）用醇基钛渣涂料的研究

互联网摘选

A mould with an oblique guide pin scroll box structure was designed for the core pulling in two directions of a mould with two cavities.

采用能解决一模两腔的两面抽芯问题的斜导柱滑块结构的模具结构，设计出电流线圈架注射模模具。

互联网摘选

The mould use LKM standard mould frame . The cavity and core use LKM 2316.

模具使用龙记模架,型腔、型芯用龙记2316.

互联网摘选

Development of injection mould with angled slide block for sequential core-pulling and delayed ejection;

模具结构中采用了定模强制脱模，顺序开模，滑动型芯延时顶出等机构。

互联网摘选

Key words: hose-connect 、 injection mould 、 take off whorl 、 side core.

关键词: 软管接头、注射模、脱螺纹、侧向抽芯.

互联网摘选

The new technology process was obtained by replacing the self-plugging items of injection mould with fusible core which was made of low melting point alloy, melting the fusible core while thermosetting plastic and taking out the product by replacing self-plugging core with fusible core.

用低熔点合金制成可熔型芯替代注射模具中的抽芯部件，在升温固化制件的同时熔化可熔型芯，用熔芯代替抽芯取出制件。

互联网摘选

Design of Hydraulic Pressure Core Pulling Mechanism for the Injection Mould of Three-way Pipe

顺水三通管注射模液压抽芯机构的设计

互联网摘选

The technological characteristics of the spare parts of three-way straight plastics pipe are analyzed, putting stress on the characteristics of the products by gating injection mould with side core pulling mechanism.

分析了三通直管塑件的工艺特点，主要分析了浇口注射模成型并且带侧向抽芯机构制品的工艺特点；

互联网摘选

The mould design sub-system consists of eight modules including formed part module, mould base module, feeding system module, core-pulling mechanism module, cooling system module, venting system module, standard part database module and pre-reset mechanism module.

模具设计子系统包括成型零件设计、模架设计、浇注系统设计、抽芯机构设计、冷却系统设计、排气系统设计、标准件库及先复位机构设计八个模块。

互联网摘选

Design of New Type of Die Casting Mould with Tightwire and Idler Wheel for Angle Core Pulling The Air Pressure Seal Equipment of the Bearings in the Idler Pulley Assembly of the WEDM

新型钢丝绳滚轮斜抽芯压铸模设计线切割机上下导轮轴承气压密封装置

互联网摘选