Tolerances的例句大全

In order to calibrate the finite element lattice nodes of tolerances efficiently, an effective direct measure approach is developed in this article, which is fulfilled by laser interferometer to measure the terminal error of machine tool directly.

为了高效标定误差有限元网格节点参数，提出了用跟踪激光干涉仪实现机床误差的直接测量方法。

互联网摘选

Testing method and standard tolerances for yarn spun on the woolen system

纺毛纱试验法及标准公差

互联网摘选

The present article is related to the analysis and discussion on tolerances of thread pitch and screwed hole in light rails and derivates the general design formula of screw pitch gauge. Consequently, the design of various screw pitch gauges for light rails can be improved.

本文对轻轨孔距及螺孔的公差进行了分析讨论，推导出孔距卡板的通用设计公式，据此可改进各种规格轻轨孔距的检查卡尺的设计。

互联网摘选

The subject is to solve the thread structure, mechanical properties, dimensional tolerances, standards modify and so on, providing higher torque, greater reliability, and interchangeably accident processing tools for drilling production.

通过该论文研究，着力解决螺纹结构形式、机械性能、尺寸公差、标准修改细化等四方面的研究工作，为钻井生产解卡提供扭矩更大、可靠性更高、能互换使用的事故处理工具。

互联网摘选

A phased array antenna requires calibration and compensation of amplitude/ phase errors due to element mutual coupling, component manufacturing and assembly tolerances, ageing, thermal distortion and component replacement.

相控阵天线由于单元间互耦、器件的制造、组装误差、老化、热变形和组件更换的影响而产生幅相误差，必须进行校准和补偿。

互联网摘选

The paper describes the O. D. and wall-thickness tolerances and internal/ external surface quality of midium and heavy wall steel pipes produced in Hengyang Steel Pipe Factory by means of φ 108mm three-roll mill complete with a 12-stand slight-stretch reducing mill.

介绍了衡阳钢管厂φ108mm三辊轧管机组配置12架微张力减径机生产中厚壁钢管的外径精度、壁厚精度及内外表面质量情况。

互联网摘选

Rolling experiments were carried out based on the analysis of rolling force and power in a three-roll planetary mill. The result shows that dimensions, surface quality and tolerances of piPes rolled with the mill can all meet the specified requirements.

在理论分析三辊行星轧制的轧制力和轧制功率的基础上，进行了轧制试验，结果表明，采用三辊行星轧机轧管，无论是尺寸范围，还是表面质量、公差均能达到预期目的。

互联网摘选

The paper, based on analyzing the errors in clamps for gear hobbing machine and gear slotting machine when positioning and tool-setting, proposes to use several important gearing tolerances to limit the errors in clamp when positioning and tool-setting.

重点分析常用的加工齿轮的滚齿机和插齿机夹具在机床上定位和对刀误差，并用常用的几个重要的齿轮公差来限定机床夹具的定位和对刀误差。

互联网摘选

Tolerances, gaps, surfaces, installation chamfers, length of bearing surface, length of stroke, frequency, speed, etc.

公差，间隙，表面，安装倒角，表面承受的长度，行程的长度，频率，速度等等。

互联网摘选

The boost pressure is a variable which is influenced by engine tolerances and ambient conditions.

增压压力是一个受发动机公差和环境条件影响的变量。

provided by jukuu

A Study of Optimal Process Tolerances Deign Based on Process Capability Index

基于工序能力指标的工序公差优化设计研究

互联网摘选

The Tooth Profile Design of Spline Hobs with Tooth Side and Bottom Grinding Tolerances

留磨花键滚刀的齿形设计

互联网摘选

Optimization of Dimensional Tolerances Bands for Ten-bar Planar Linkage in Tricot Machine

经编机平面十杆机构结构参数公差带优化综合

互联网摘选

All the working dimensions will be finally determined according to the minimum margin and calculated margin tolerances.

最后根据最小余量及计算出的余量公差确定出全部工序尺寸。

互联网摘选

Research progress of hydrodynamic journal bearing system dynamics allowing for manufacturing tolerances

考虑制造误差时滑动轴承转子系统动力学研究进展

互联网摘选

Analysis and Application of National Standard on The Linear Dimensions General Tolerances

线性尺寸一般公差国标的分析和应用

互联网摘选

Relationship between Runout Tolerances and Application in Practice

跳动公差之间的关系及在实际中的应用

互联网摘选

Research on the Connections between Runout Tolerance and Other Geometrical Tolerances

跳动公差与其它形位公差的关系研究

互联网摘选

Classical EVA requires the accurate determination of initial cost as a function of tolerances and the cost of failure.

传统的EVA需要精确确定初始成本作为公差的函数以及破坏成本。

互联网摘选

By using the partial differential theory and technological size chain principle of multivariate function, this paper puts forward a simplified calculating method for tolerance in plane size chain, through which people can calculate the plane system size tolerance and other size tolerances in plane size chain.

应用多元函数的偏微分理论和工艺尺寸链原理，提出一种简化平面尺寸链公差计算的方法，应用此方法可以简捷地计算平面孔系尺寸公差及平面尺寸链中的其它尺寸公差。

互联网摘选