Special Knockout for Engine Crankshaft Bearing of Motorcycle

1、

Research For Improvement on Crankshaft Bearing Lubrication of IC Engine

改善内燃机曲轴轴承润滑状态的研究

互联网摘选

2、

In order to manufacture high-quality crankshafts with high efficiency without crankshaft mill and satisfy the demand for mass production, we designed the process of crankshaft lathe so as to meet the corresponding process accuracy.

为了在无曲轴磨床的情况下，高效制造出高质量的曲轴，以满足大批量生产的要求，对曲轴车床加工进行了工艺设计，使其达到了相应的加工精度要求。

互联网摘选

3、

The dental abrasive testing machine applies a V-like swing arm to driving the wearing part to move along the slope back and forth, which is connected with an eccentric wheel fixed on the crankshaft of the gear motor through a connecting rod.

该机采用V形摆动臂来驱动磨耗部分沿斜面作往复磨耗运动，V形摆动臂通过连接杆与减速电机轴上的偏心轮连接。

互联网摘选

4、

Control of Positional Accuracy for Keyways in Crankshaft Timing Gear Journals

曲轴齿轮轴颈键槽位置精度控制方法

互联网摘选

5、

The study showed that the structural dimensions played an important role the crankshaft gear stress. Based on these, on analyze the impact law of the structural dimensions affect to the interference fit was mainly focused.

研究表明结构尺寸对曲轴齿轮应力影响较大，在此基础上着重分析了结构尺寸对过盈量的影响规律。

互联网摘选

6、

The primary drive gear ( crankshaft gear) and the primary driven gear are the source of noise due to their high speed and bigger reduction ratio.

作为摩托车初级传动的曲轴齿轮及初级从动齿轮，由于转速高及降速比大，是产生噪声的主要因素。

互联网摘选

7、

The relation between the related structural dimensions of interference fit, the contact state, the running state and the crankshaft gear stress was mainly investigated.

重点探讨了过盈联接相关结构尺寸、接触状态以及运转状态等因素与曲轴齿轮应力的关系。

互联网摘选

8、

Therefore, the finite element method was used in this article to systematically study the Interference technology of the crankshaft gear.

为此本文利用有限元方法，对曲轴齿轮过盈联接技术展开了系统的研究。

互联网摘选

9、

Fault Diagnosis of Crankshaft Main Journal Grinder Based on Vibration Technique

基于振动诊断技术的曲轴主轴颈磨床故障诊断

互联网摘选

10、

Design of Wheel Dressing Program for 4R Crankshaft Grinder

4R曲轴磨床砂轮修整程序设计

互联网摘选

11、

Synchronous Control for Crankshaft Grinder Head-tail Stock Based on AC Servo

基于交流伺服驱动的曲轴磨床头尾架同步控制方法

互联网摘选

12、

Refitting Toyoda Crankshaft Grinder with Siemens 840D

用西门子840D系统改造丰田七砂轮曲轴磨床

互联网摘选

13、

By the modal experimental of the crankshaft, the validity of the finite element model about crankshaft which includes pulley and flywheel was verified.

通过曲轴的模态试验验证了曲轴有限元模型的准确性。

互联网摘选

14、

The models of crankshaft with flywheel and pulley and crankshaft without flywheel and pulley were analyzed and compared.

对曲轴带飞轮和皮带轮及不带飞轮和皮带轮两种情况下进行了模态分析，并进行了比较。

互联网摘选

15、

Fit the crankshaft belt pulley with a helper.

与一个助手装配曲轴皮带轮。

provided by jukuu

16、

Water pump and cooling fan of traditional cars are usually driven by the engine through V belt, which is intertwined between crankshaft pulley and water pump pulley. Therefore, the rotational speed of water pump is in proportional relationship with the engine speed.

而传统汽车的水泵和散热风扇一般由发动机曲轴通过V带传动，传动带环绕在曲轴带轮与水泵带轮之间，因此水泵转速与发动机转速成比例关系。

互联网摘选

17、

The engine number can be found on the front right of the crankcase next to the crankshaft pulley.

可以在曲轴皮带轮旁边的曲轴箱右前方找到发动机号。

provided by jukuu

18、

Our products mainly include crankshaft pulley, water pump pulley, air-conditioner pulley and electric motor pulley, tensioner pulley, damping pulley, Idler assy pulley.

曲轴皮带轮、水泵皮带轮、空调皮带轮、电机皮带轮、张紧轮、减震皮带轮及怠速轮的生产及安装。

互联网摘选

19、

Only turn engine using the crankshaft pulley, not at the camshafts.

仅能使用曲轴皮带轮转动发动机，而不是在凸轮轴处转动。

provided by jukuu

20、

A Crankshaft Fluctuation Sensor ( CKF) is located near the bottom of the timing cover where it generates a signal as the crankshaft timing chain sprocket rotates past it.

曲轴位置传感器安装在定时器壳底部附近，产生一个曲轴定时链轮齿通过的信号。

互联网摘选