a study on the testing of cotton short fiber content

1、

influence of steel fiber content on mechanical properties of polymer concrete

钢纤维含量对树脂混凝土力学性能的影响

互联网摘选

2、

it is showed that by using the phenolic resin and the fiber, the clutch friction materials could be manufactured with good properties such as stable friction coefficient, low wear rate, high fade resistance at 350 ℃, and suitable porosity.

结果表明，采用三组份酚醛树脂和混杂纤维可以制备出摩擦性能良好，350℃不发生热衰退的离合器摩擦材料，且材料具有合适的孔隙率。

互联网摘选

3、

because of the better fiber orientation, the friction coefficient on fingernail is a little lower than that on chicken claws at the same loading conditions.

由于具有更好的纤维取向性，指甲表面的划痕摩擦系数略低于鸡爪。

互联网摘选

4、

the relations between compression elastic rebound characteristic of assorted fiber enhanced paper base friction materials and pressure, fiber content and factor of porosity are studied.

研究了混杂纤维增强的纸基摩擦材料压缩回弹特性与压缩压力、纤维含量及孔隙率之间的关系。

互联网摘选

5、

effect of short kevlar fiber on performances of friction materials

Kevlar短纤维对摩擦材料性能的影响效应

互联网摘选

6、

development of reinforcing fiber used in automotive friction material

汽车摩擦材料用增强纤维的研究现状与发展趋势

互联网摘选

7、

the antibacterial wool fiber showed excellent friction performance and wash resistance property. the improved degree of disorder in the molecular structure during the modification resulted in the good mechanical property and thermal stability.

在改性过程中，抗菌羊毛纤维分子的有序化程度提高，使其具有良好的力学性能和热稳定性。

互联网摘选

8、

effect of carbon fiber content on friction and wear properties of al_2o_3+ c/ zl109 hybrid composites

碳纤维含量对Al2O3+C/ZL109混杂复合材料摩擦磨损性能的影响

互联网摘选

9、

investigation on wear properties of ptfe composites filled with short glass fiber in dry friction condition

短玻纤填充PTFE复合材料磨损性能研究

互联网摘选

10、

influence of carbon fiber percent on friction coefficient of copper-graphite brush

碳纤维含量对铜-石墨电刷摩擦因数的影响

互联网摘选

11、

in this paper, research about fiber reinforced ceramic friction materials is briefly reviewed.

本文对纤维增强陶瓷摩擦材料的研究进展进行了简要的综述。

互联网摘选

12、

research of electroless copper plating technology of carbon fiber and its friction performances

碳纤维表面化学镀铜工艺优化及摩擦性能研究

互联网摘选

13、

on the basis of optimizing carbon fiber composite friction material with the orthogonal design, the friction and wear characteristics and the wear mechanism of carbon fiber composite material are studied against the actual working conditions of automotive brake linings.

在采用正交设计优化碳纤维复合摩阻材料的基础上，针对汽车制动器衬片的实际工况，研究了碳纤维复合摩阻材料的摩擦磨损特性及磨损机制。

互联网摘选

14、

thus, a 21% glass fiber non-asbestos friction material of clutch lining was prepared, its properties all meet the gb national standards and will be developed industrially.

含21%玻璃纤维的无石棉摩阻材料离合器片，其性能已符合国家标准，可以进行扩大生产。

互联网摘选

15、

on certain conditions, the two treatment options can improve the fiber surface friction coefficient without obvious reduction of the fiber strength and elongation.

在一定的处理条件下，两种处理方案均可以在保证纤维强伸性降低不大的情况下提高纤维的表面摩擦因数。

互联网摘选

16、

fiber reinforced friction composites

纤维增强摩擦复合材料

互联网摘选

17、

study of non-asbestos high-friction-coefficient materials ⅰ. glass fiber reinforced friction materials

无石棉摩阻材料的研究&Ⅰ.玻璃纤维增强摩阻材料

互联网摘选

18、

study on friction and wear characteristics of carbon fiber composite friction materials for automotive

汽车用碳纤维复合摩阻材料的摩擦磨损特性研究

互联网摘选

19、

the research of carbon fiber reinforced friction materials

碳纤维增强摩擦制动材料研究

互联网摘选

20、

influence of carbon fiber in friction materials on wear resistance

碳纤维对增强的摩阻材料的摩擦磨损特性的影响

互联网摘选