Implementation of Diesel Fuel-Natural Gas Dual fuel Electricity Spurt System Control Strategy

1、

Application and development of spurting concrete rapid setting admixture

喷射混凝土速凝剂的应用与发展

互联网摘选

2、

Experimental Study of Relationships Between Age and Strength of Powder Spurting Pile in Different Temperature

粉喷桩在不同温度下龄期与强度关系的试验研究

互联网摘选

3、

Water spurting from a broken pipe

从破裂的管子中喷出的水

互联网摘选

4、

And right from the start, it seemed Mr. Obama enjoyed having the first lady steal some of the spotlight.

而从一开始，奥巴马就习惯让他的第一夫人抢走一些风头。

互联网摘选

5、

Prior to the inauguration, some fans joked that Beyonce should drop an album as Trump was being sworn in, and in doing so steal the spotlight from the new commander in chief.

在就职典礼之前，一些粉丝就开玩笑称碧昂斯应该在特朗普宣誓就职时抛出一张专辑，这样就可以抢走这位新总统的风头。

互联网摘选

6、

Fashion Comments: bright navy blue, absolutely steal the spotlight master.

时尚点评：鲜艳的宝蓝色，绝对是抢镜高手。

互联网摘选

7、

But its focus on the emerging economies may soon steal the spotlight.

但它对新兴经济体的关注可能很快就会吸引世人的注意力。

互联网摘选

8、

It will be helpful to improving the filling velocity when the sprue length and sprue areas are controlled to some extent.

一定的直浇道长度及直浇道面积有利于提高铝液的充型速度。

互联网摘选

9、

The system includes sprue, runner, gate, overflow launder, venting launder.

该系统包括压铸模浇注系统的直浇道、横浇道、内浇口、溢流槽和排气槽。

互联网摘选

10、

To decrease the casting pinholes, there should be higher pouring temperature and a suitable sprue height and area.

为减少铸铝件的针孔，铝合金消失模铸造应有适当高的浇注温度和合适的直浇道高度及面积，并尽量采用空心直浇道。

互联网摘选

11、

Normal small intestinal mucosa is seen at the left, and mucosa involved by celiac sprue at the right.

左侧为正常小肠黏膜，右侧为脂肪痢黏膜。

互联网摘选

12、

Annular secondary flow at die entrance, which was perpendicular to sprue, was proved in the experiment.

实验证实PP-R熔体在入口区发生了垂直于主流道方向的环向次级流动。

互联网摘选

13、

The injection mold with double parting surfaces was usually used in the multi-cavity structure and pin sprue injection system.

双分型面注射模，常用于一模多腔、点浇口形式浇注系统的注射模。

互联网摘选

14、

Here is the cast faceplate with the gate and sprue still attached.

以下是与门面板和浇道演员仍然重视。

互联网摘选

15、

MPI-based optimization design of injection forming sprue

基于MPI的塑件浇口优化设计

互联网摘选

16、

The Defects of the Submarine Gate and Its Maintenance MPI-based optimization design of injection forming sprue

潜伏式浇口的缺陷及维修基于MPI的塑件浇口优化设计

互联网摘选

17、

The Sprue and Gate Design of a Multi-cavities Injection Mold for Special Hooks

塑料扣码多腔注射模浇口的设计

互联网摘选

18、

Discuss on Structures of Automatic-Sheared Side Sprue for Injection Mold

注射模侧浇口自动切断结构探讨

互联网摘选

19、

Research of relationship of the sprue designing shrinkage cavity of Cr-Ni alloy cast crown bridge.

目的：探讨镍铬合金铸造冠桥铸件缩孔与铸道设计的关系。

互联网摘选

20、

Computer-aided design of sprue in extrusion die head for plastic profiled bar inner rib

塑料异型材挤出模头内筋流道的辅助设计

互联网摘选