Evaluation Model of Mobile Input Devices

1、

The structure of intersecting Lap joint Between steel pipe has been widely applied in engineering project, such as Oil and gas pipelines, Pressure vessel and Various forms of pipe truss structure.

工程中钢管与钢管的相贯搭接广泛的应用于油气管道、压力容器以及各种形式的管桁架钢结构中。

互联网摘选

2、

Analysis of Adhesive Lap Joint Evaluation includes appearance of weld, effect of flux on penetration, microstructure of weld, chemical compositions of weld and base material and mechanical properties.

内容包括焊缝外观形貌、熔深效果、接头微观组织、化学成分及接头力学性能分析。

互联网摘选

3、

Taking the form of lap joint as an example, the effect of final assembling deviation affect by the assembly sequence was analyzed by adopting the method of worse condition.

以搭接接头形式为例，采用最坏情况法分析了装配顺序对最终装配偏差的影响。

互联网摘选

4、

The BEM technique for adhesive-bonded structure proves valid by comparing the stress distribution for double lap joint calculated in this paper with that calculated by finite element method.

对双搭接接头进行了边界元应力分析，并和有限元结果进行了对比，从而证实本文方法的有效性。

互联网摘选

5、

Based on the principle and process of laser transmission welding, the lap joint form was taken and the key technology and difficulty of welding were also considered.

基于激光透射焊接的原理和过程，采取搭接接头形式进行焊接，同时焊接关键技术和难点也被考虑。

互联网摘选

6、

Using boundary element method, the interfacial streeses of adhensive lap joint with either perfect or imperfect interface are studied.

采用边界元法计算分析了具有理想界面和非理想界面的双板条胶合搭接连接的界面应力。

互联网摘选

7、

Interfacial Stresses of an Adhensive Lap Joint

胶合搭接连接的界面应力

互联网摘选

8、

By comparing the results of buckling analysis, the effects of material nonlinearity, geometric imperfection and lap joint on stability were studied.

分析了材料非线性、几何缺陷和筒壁搭接对稳定性能的影响。

互联网摘选

9、

We can obtain the good appearance and defect-free brass and aluminum alloy lap joint when selecting the appropriate parameters.

焊接时选取合适的工艺参数，可以获得外观形貌良好且无缺陷的异种材料焊接接头。

互联网摘选

10、

To join ( pieces, as of wood) by means of a scarf or lap joint.

使搭接用凿槽或搭接的方法连结（小块，例如木头的）

互联网摘选

11、

This paper is to discuss the interlaminar stresses of adhesive lap joint by the energy method without considering the adhesive layer.

本文以能量法求解无胶层厚度的搭接接头的层间应力。

互联网摘选

12、

The results indicate that good lap joint between aluminum and galvanized steel sheet can be made in appropriate parameters.

试验结果表明，铝和镀锌钢能得到成形良好的搭接接头。

互联网摘选

13、

Analysis of Adhesive Lap Joint

胶合搭接接头凿岩机钎杆的寿命分析

互联网摘选

14、

Influence of Elastic Modulus of Adhesive on the Stress and Strain Distribution in Aluminium Single Lap Joint

胶粘剂弹性模量对铝合金单搭接接头应力应变分布的影响

互联网摘选

15、

The shear strength and elongation of the lap joint increase with the increase of strain rate.

焊点的剪切强度及伸长量随应变速率的增加而增加。

互联网摘选

16、

Improvement of Steel Wire Rope Core Belt Lacing Lap Joint Craftwork

钢丝绳芯输送带接头搭接工艺的改进

互联网摘选

17、

However, further increasing of RE content would degrade the shear properties of the lap joint.

而当稀土含量进一步增加时，焊点的强度及塑性均下降。

互联网摘选

18、

Numerical analysis on stress distribution in adhesive-welded double lap joint of aluminum

铝胶焊双搭接接头上应力分布的数值分析

互联网摘选

19、

Research and optimization design of a riveted longitudinal lap joint in integral panel structure

整体壁板结构纵向连接接头的优化设计

互联网摘选

20、

The Influence of Loading Speed on the Shear Strength of Single Lap Joint Under Testing

加载速率对胶接单搭接头剪切强度的影响

互联网摘选