The electric control system based on network for the nitrogen protection kiln is presented.

The realization of embedded internet technology makes a try to apply technology of information network to industrial distribution control.

本文中嵌入式Internet技术的实现对信息网技术应用于工业现场分布式控制做了有益的尝试。

互联网摘选

Distributed control system ( DCS) is gradually replaced by field bus Control system ( FCS) based on intelligent field devices of all-digital communications.

基于全数字化通信的智能现场装置的现场总线控制系统（FCS：Field Bus Control System）正在逐渐取代分布式控制系统（DCS：DIstributed Control System）。

互联网摘选

Embedded Web-based Real-time Ethernet Distributed Control System

基于嵌入式Web的实时以太网分布式控制系统

互联网摘选

The PCS7 DCS technology, combined with Siemens'project management capabilities, led to the selection.

PCS7的分布式控制系统技术，结合西门子的项目管理能力，使我们选择了他们。

互联网摘选

The paper analyses the problem about the developing of DCS system, compares DCS with FCS, and brings out the precept about amalgamation DCS and FCS.

分析了分布式控制系统（DCS）发展存在的问题，对DCS和现场总线控制系统（FCS）进行了比较，提出将DCS和FCS融合的方案。

互联网摘选

Rapid Realization of Networked Control Systems Based on NetCon

基于NetCon的网络化控制系统快速实现

互联网摘选

The simulation of frequency and load perturbation indicate that μ controller has superior control effect than H ∞ controller and conventional PID controller. Next, the wide-area measuring system ( WAMS) based on TCSC networked control strategy is presented.

对水电机组的频率和负荷扰动仿真分析表明，μ综合控制器比H∞控制器和常规的PID控制器具有良好的控制效果。提出了基于广域测量信号的TCSC网络化控制方案。

互联网摘选

This paper deals with the problem of stabilization and L_2-gain analysis of networked control systems subject to actuator saturation.

针对含执行器饱和网络化控制系统，研究其镇定问题与L2增益分析。

互联网摘选

The real-time network control based on Matlab/ Simulink for actual industrial objects requirements Matlab software running on the PC, and the need to use OPC communication technologies, however, these operations cumbersome and complex.

而基于Matlab/simulink对实际工业对象进行实时的网络化控制要求PC机上运行Matlab软件，并且需要利用OPC通讯技术，然而这些操作繁琐复杂。

互联网摘选

Based on Lyapunov stability theory, through using linear matrix inequality, this paper proposes analysis and synthesis method for the networked control systems with different plant by designed new controllers and observers.

本文利用Lyapunov稳定性理论，采用线性矩阵不等式这一有效的工具，通过设计一些新的观测器和控制器，对含有不同被控对象的网络化控制系统进行了分析和控制。

互联网摘选

With regards to the characteristics of uncertain transmission delay and packet dropout of networked control system ( NCS), a distributed model is proposed in this paper.

针对网络化控制系统（NCS）具有不确定性的传输迟延与数据丢包特性，设计了一个分布式的网络化控制系统模型。

互联网摘选

Finally, based on the realization of the above systems, we built a clock synchronization test platform of networked control system based on ICE. The communication system has been tested clock synchronization to verify its capability.

最后，在实现上述系统的基础上，构建了基于ICE的网络化控制系统的时钟同步测试平台，并对系统进行了时钟同步测试，从而检验了网络通信平台的工作能力。

互联网摘选

The effectiveness of the proposed design approach are illustrated by numerical examples. Finally, the stochastic stability analysis and design of networked control sys-

数值例子说明了所给设计方法的有效性。最后，对两种不同的网络化控制系统（NCS）模型，研究了NCS的随机稳定性分析与设计问题。

互联网摘选

Feedback control systems in which the control loops are closed through data and command communicating networks are called networked control systems ( NCS).

网络化控制系统（NCS）是一种可以通过数字通信网络进行数据和命令传输的闭环反馈控制系统。

互联网摘选

For uncertain networked control systems, the problem of robust control for uncertain continuous linear time-delay systems based on Lyapunov theory and descriptor system model transformation method is studied.

分别对于不确定网络化控制系统，采用Lyapunov理论及奇异系统模型变换的方法，研究其鲁棒控制问题。

互联网摘选

In specific, a novel Markovian jump linear system with time-varying delays is used to model the networked control system ( NCS).

本文将网络化控制系统NCS建模为带有时延的马尔可夫跳变系统。

互联网摘选

Time delay uncertainty among the sensors, actuators and controllers is a key problem for the networked control system ( NCS).

传感器，执行器以及控制器之间的延迟不确定性问题是网络化控制系统（NCS）的一个关键问题。

互联网摘选

Guaranteed cost control for Lurie networked control systems

Lurie网络化控制系统的保性能控制

互联网摘选

At last, some characteristics of networked control system are summarized.

在文末，概括XML-RPC应用于网络化控制系统的一些特点。

互联网摘选

This paper proposes two methods about delay estimation and the delay data procurement on-line to deal with the random delay of networked control system ( NCS), then sets up a mathematical plant model.

本文针对网络化控制系统（NetWorked Control System，简称NCS）的随机延时，提出了延时估计和在线获得延时数据的两种方法，建立控制对象的数学模型。

互联网摘选